View SAK-C164CI-8EM_1314754.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

never stop thinking. microcontrollers data sheet, v2.0, may 2001 c164ci/si c164cl/sl 16-bit single-chip microcontroller
edition 2001-05 published by infineon technologies ag, st.-martin-strasse 53, d-81541 mnchen, germany ? infineon technologies ag 2001. all rights reserved. attention please! the information herein is given to describe certain components and shall not be considered as warranted characteristics. terms of delivery and rights to technical change reserved. we hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. infineon technologies is an approved cecc manufacturer. information for further information on technology, delivery terms and conditions and prices please contact your nearest infineon technologies office in germany or our infineon technologies representatives worldwide. warnings due to technical requirements components may contain dangerous substances. for information on the types in question please contact your nearest infineon technologies office. infineon technologies components may only be used in life-support devices or systems with the express written approval of infineon technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. if they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
microcontrollers data sheet, v2.0, may 2001 never stop thinking. c164ci/si c164cl/sl 16-bit single-chip microcontroller
controller area network (can): license of robert bosch gmbh c164ci revision history: 2001-05 v2.0 previous version: 1999-08 1998-02 (preliminary) 04.97 (advance information) page subjects (major changes since last revision) 1) 1) these changes refer to the last two versions. version 1998-02 covers otp and rom derivatives, while version 1999-08 ist the most recent one. all converted to infineon layout 1 operating frequency up to 25 mhz 1 et al. references to flash removed 1 timer unit with three timers 1 , 12 , 73 on-chip xram described 2 derivative table updated 10 supply voltage is 5 v 21 functionality of reduced capcom6 corrected 22 f timer description improved 29 , 30 sections ?oscillator watchdog? and ?power management? added 37 pocon reset values adjusted 41 to 73 parameter section reworked we listen to your comments any information within this document that you feel is wrong, unclear or missing at all? your feedback will help us to continuously improve the quality of this document. please send your proposal (including a reference to this document) to: mcdocu.comments@infineon.com
data sheet 1 v2.0, 2001-05 c164ci 16-bit single-chip microcontroller c166 family c164ci/si, c164cl/sl high performance 16-bit cpu with 4-stage pipeline ? 80 ns instruction cycle time at 25 mhz cpu clock ? 400 ns multiplication (16 16 bit), 800 ns division (32 / 16 bit) ? enhanced boolean bit manipulation facilities ? additional instructions to support hll and operating systems ? register-based design with multiple variable register banks ? single-cycle context switching support ? 16 mbytes total linear address space for code and data ? 1024 bytes on-chip special function register area 16-priority-level interrupt system with 32 sources, sample-rate down to 40 ns 8-channel interrupt-driven single-cycle data transfer facilities via peripheral event controller (pec) clock generation via on-chip pll (factors 1:1.5/2/2.5/3/4/5), via prescaler or via direct clock input on-chip memory modules ? 2 kbytes on-chip internal ram (iram) ? 2 kbytes on-chip extension ram (xram) ? up to 64 kbytes on-chip program mask rom or otp memory on-chip peripheral modules ? 8-channel 10-bit a/d converter with programmable conversion time down to 7.8 s ? 8-channel general purpose capture/compare unit (capcom2) ? capture/compare unit for flexible pwm signal generation (capcom6) (3/6 capture/compare channels and 1 compare channel) ? multi-functional general purpose timer unit with 3 timers ? two serial channels (synchronous/asynchronous and high-speed-synchronous) ? on-chip can interface (rev. 2.0b active) with 15 message objects (full can/basic can) ? on-chip real time clock up to 4 mbytes external address space for code and data ? programmable external bus characteristics for different address ranges ? multiplexed or demultiplexed external address/data buses with 8-bit or 16-bit data bus width ? four optional programmable chip-select signals idle, sleep, and power down modes with flexible power management programmable watchdog timer and oscillator watchdog up to 59 general purpose i/o lines, partly with selectable input thresholds and hysteresis
c164ci/si c164cl/sl data sheet 2 v2.0, 2001-05 supported by a large range of development tools like c-compilers, macro-assembler packages, emulators, evaluation boards, hll-debuggers, simulators, logic analyzer disassemblers, programming boards on-chip bootstrap loader 80-pin mqfp package, 0.65 mm pitch this document describes several derivatives of the c164 group. table 1 enumerates these derivatives and summarizes the differences. as this document refers to all of these derivatives, some descriptions may not apply to a specific product. for simplicity all versions are referred to by the term c164ci throughout this document. table 1 c164ci derivative synopsis derivative 1) 1) this data sheet is valid for rom(less) devices starting with and including design step ab, and for otp devices starting with and including design step da. program memory capcom6 can interf. operating frequency sak-c164ci-8r[25]m saf-c164ci-8r[25]m 64 kbyte rom full function can1 20 mhz, [25 mhz] sak-c164si-8r[25]m saf-c164si-8r[25]m 64 kbyte rom full function --- 20 mhz, [25 mhz] sak-c164cl-8r[25]m saf-c164cl-8r[25]m 64 kbyte rom reduced fct. can1 20 mhz, [25 mhz] sak-c164sl-8r[25]m saf-c164sl-8r[25]m 64 kbyte rom reduced fct. --- 20 mhz, [25 mhz] sak-c164cl-6r[25]m saf-c164cl-6r[25]m 48 kbyte rom reduced fct. can1 20 mhz, [25 mhz] sak-c164sl-6r[25]m saf-c164sl-6r[25]m 48 kbyte rom reduced fct. --- 20 mhz, [25 mhz] sak-c164ci-l[25]m saf-c164ci-l[25]m --- full function can1 20 mhz, [25 mhz] SAK-C164CI-8EM saf-c164ci-8em 64 kbyte otp full function can1 20 mhz
c164ci/si c164cl/sl data sheet 3 v2.0, 2001-05 ordering information the ordering code for infineon microcontrollers provides an exact reference to the required product. this ordering code identifies: the derivative itself, i.e. its function set, the temperature range, and the supply voltage the package and the type of delivery. for the available ordering codes for the c164ci please refer to the ?product catalog microcontrollers? , which summarizes all available microcontroller variants. note: the ordering codes for mask-rom versions are defined for each product after verification of the respective rom code. introduction the c164ci derivatives of the infineon c166 family of full featured single-chip cmos microcontrollers are especially suited for cost sensitive applications. they combine high cpu performance (up to 12.5 million instructions per second) with high peripheral functionality and enhanced io-capabilities. they also provide clock generation via pll and various on-chip memory modules such as program rom or otp, internal ram, and extension ram. figure 1 logic symbol mcl04869 v dd v ss xtal1 xtal2 port 0 16 bit port 1 16 bit port 3 9 bit port 4 6 bit port 8 4 bit port 5 8 bit rstin rstout nmi ea ale rd wr/wrl v aref v agnd c164ci
c164ci/si c164cl/sl data sheet 4 v2.0, 2001-05 pin configuration (top view) figure 2 *) the marked pins of port 4 and port 8 can have can interface lines assigned to them. table 2 on the pages below lists the possible assignments. the marked input signals are available only in devices with a full-function capcom6. they are not available in devices with a reduced-function capcom6. mcp04870 80 60 21 1 v aref p5.4/an4/t2eud 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 v d d 22 */p4.5/a20 23 */p4.6/a21 24 25 rd w r/w rl 26 ale 27 28 vpp/ea p0l.0/ad0 29 p0l.1/ad1 30 31 p0l.2/ad2 p0l.3/ad3 32 p0l.4/ad4 33 34 p0l.5/ad5 p0l.6/ad6 35 p0l.7/ad7 36 37 38 p0h.2/ad10 39 40 p0h.0/ad8 p5.3/an3 79 78 77 76 75 p8.3/cc19io /* 74 73 72 71 rstou t 70 69 rstin 68 p1h.7/a15/cc27io 67 66 65 64 63 62 61 59 58 p1l.6/a6/cout63 57 56 xtal1 55 xtal2 54 53 p1l.5/a5/cout62 52 p1l.4/a4/cc62 51 50 p1l.3/a3/cout61 p1l.2/a2/cc61 49 p1l.1/a1/cout60 48 47 p1l.0/a0/cc60 p0h.7/ad15 46 p0h.6/ad14 45 44 43 p0h.3/ad11 42 41 p5.5/an5/t4eud v ss p3.4/t3eud p3.6/t3in p3.8/mrst p3.9/mtsr p3.10/txd0 p3.13/sclk p3.12/bhe/wrh p3.15/clkout/fout p4.0/a16/cs3 v d d v d d p0h.4/ad12 p0h.5/ad13 p5.6/an6/t2in p5.7/an7/t4in v dd p4.1/a17/cs2 p4.2/a18/cs1 v ss p4.3/a19/cs0 p0h.1/ad9 v ss v dd v ss p1l.7/a7/ctrap p1h.0/a8/ cc6pos0 /ex0in v ss v a g n d p5.2/an2 p5.1/an1 p5.0/an0 p8.2/cc18io /* p8.1/cc17io /* p8.0/c c16io /* nm i p1h.5/a13/cc25io p1h.4/a12/cc24io p1h.3/a11/exin/t7in p1h.2/a10/ cc 6po s2 /ex2in p1h.1/a9/ cc6po s1 /ex1in p1h.6/a14/cc26io p3.11/rxd0 c164ci
c164ci/si c164cl/sl data sheet 5 v2.0, 2001-05 table 2 pin definitions and functions symbol pin no. input outp. function p5 p5.0 p5.1 p5.2 p5.3 p5.4 p5.5 p5.6 p5.7 76 77 78 79 2 3 4 5 i i i i i i i i i port 5 is an 8-bit input-only port with schmitt-trigger charact. the pins of port 5 also serve as analog input channels for the a/d converter, or they serve as timer inputs: an0 an1 an2 an3 an4, t2eud gpt1 timer t2 ext. up/down ctrl. inp. an5, t4eud gpt1 timer t4 ext. up/down ctrl. inp. an6, t2in gpt1 timer t2 input for count/gate/reload/capture an7, t4in gpt1 timer t4 input for count/gate/reload/capture p3 p3.4 p3.6 p3.8 p3.9 p3.10 p3.11 p3.12 p3.13 p3.15 8 9 10 11 12 13 14 15 16 io i i i/o i/o o i/o o o i/o o o port 3 is a 9-bit bidirectional i/o port. it is bit-wise programmable for input or output via direction bits. for a pin configured as input, the output driver is put into high- impedance state. port 3 outputs can be configured as push/ pull or open drain drivers. the input threshold of port 3 is selectable (ttl or special). the following port 3 pins also serve for alternate functions: t3eud gpt1 timer t3 external up/down control input t3in gpt1 timer t3 count/gate input mrst ssc master-receive/slave-transmit inp./outp. mtsr ssc master-transmit/slave-receive outp./inp. txd0 asc0 clock/data output (async./sync.) rxd0 asc0 data input (async.) or inp./outp. (sync.) bhe external memory high byte enable signal, wrh external memory high byte write strobe sclk ssc master clock output / slave clock input. clkout system clock output (= cpu clock), fout programmable frequency output
c164ci/si c164cl/sl data sheet 6 v2.0, 2001-05 p4 p4.0 p4.1 p4.2 p4.3 p4.5 p4.6 17 18 19 22 23 24 io o o o o o o o o o i o o port 4 is a 6-bit bidirectional i/o port. it is bit-wise programmable for input or output via direction bits. for a pin configured as input, the output driver is put into high- impedance state. port 4 outputs can be configured as push/ pull or open drain drivers. the input threshold of port 4 is selectable (ttl or special). port 4 can be used to output the segment address lines, the optional chip select lines, and for serial interface lines: 1) a16 least significant segment address line, cs3 chip select 3 output a17 segment address line, cs2 chip select 2 output a18 segment address line, cs1 chip select 1 output a19 segment address line, cs0 chip select 0 output a20 segment address line, can1_rxd can 1 receive data input a21 most significant segment address line, can1_txd can 1 transmit data output rd 25 o external memory read strobe. rd is activated for every external instruction or data read access. wr / wrl 26 o external memory write strobe. in wr -mode this pin is activated for every external data write access. in wrl -mode this pin is activated for low byte data write accesses on a 16-bit bus, and for every data write access on an 8-bit bus. see wrcfg in register syscon for mode selection. ale 27 o address latch enable output. can be used for latching the address into external memory or an address latch in the multiplexed bus modes. table 2 pin definitions and functions (cont ? d) symbol pin no. input outp. function
c164ci/si c164cl/sl data sheet 7 v2.0, 2001-05 ea / v pp 28 i external access enable pin. a low level at this pin during and after reset forces the c164ci to latch the configuration from port0 and pin rd , and to begin instruction execution out of external memory. a high level forces the c164ci to latch the configuration from pins rd and ale, and to begin instruction execution out of the internal program memory. ? romless ? versions must have this pin tied to ? 0 ? . note: this pin also accepts the programming voltage for the otp derivatives. port0 p0l.0-7 p0h.0-7 29- 36 37-39, 42-46 io port0 consists of the two 8-bit bidirectional i/o ports p0l and p0h. it is bit-wise programmable for input or output via direction bits. for a pin configured as input, the output driver is put into high-impedance state. in case of an external bus configuration, port0 serves as the address (a) and address/data (ad) bus in multiplexed bus modes and as the data (d) bus in demultiplexed bus modes. demultiplexed bus modes: data path width: 8-bit 16-bit p0l.0 ? p0l.7: d0 ? d7 d0 ? d7 p0h.0 ? p0h.7: i/o d8 ? d15 multiplexed bus modes: data path width: 8-bit 16-bit p0l.0 ? p0l.7: ad0 ? ad7 ad0 ? ad7 p0h.0 ? p0h.7: a8 ? a15 ad8 ? ad15 table 2 pin definitions and functions (cont ? d) symbol pin no. input outp. function
c164ci/si c164cl/sl data sheet 8 v2.0, 2001-05 port1 p1l.0-7 p1h.0-7 p1l.0 p1l.1 p1l.2 p1l.3 p1l.4 p1l.5 p1l.6 p1l.7 p1h.0 p1h.1 p1h.2 p1h.3 p1h.4 p1h.5 p1h.6 p1h.7 47-52, 57-59 59, 62-68 47 48 49 50 51 52 57 58 59 62 63 64 65 66 67 68 io i/o o i/o o i/o o o i i i i i i i i i/o i/o i/o i/o port1 consists of the two 8-bit bidirectional i/o ports p1l and p1h. it is bit-wise programmable for input or output via direction bits. for a pin configured as input, the output driver is put into high-impedance state. port1 is used as the 16-bit address bus (a) in demultiplexed bus modes and also after switching from a demultiplexed bus mode to a multiplexed bus mode. the following port1 pins also serve for alt. functions: cc60 capcom6: input / output of channel 0 cout60 capcom6: output of channel 0 cc61 capcom6: input / output of channel 1 cout61 capcom6: output of channel 1 cc62 capcom6: input / output of channel 2 cout62 capcom6: output of channel 2 cout63 output of 10-bit compare channel ctrap capcom6: trap input ctrap is an input pin with an internal pullup resistor. a low level on this pin switches the compare outputs of the capcom6 unit to the logic level defined by software. cc6pos0 capcom6: position 0 input, **) ex0in fast external interrupt 0 input cc6pos1 capcom6: position 1 input, **) ex1in fast external interrupt 1 input cc6pos2 capcom6: position 2 input, **) ex2in fast external interrupt 2 input ex3in fast external interrupt 3 input, t7in capcom2: timer t7 count input cc24io capcom2: cc24 capture inp./compare outp. cc25io capcom2: cc25 capture inp./compare outp. cc26io capcom2: cc26 capture inp./compare outp. cc27io capcom2: cc27 capture inp./compare outp. note: the marked (**) input signals are available only in devices with a full function capcom6. table 2 pin definitions and functions (cont ? d) symbol pin no. input outp. function
c164ci/si c164cl/sl data sheet 9 v2.0, 2001-05 xtal2 xtal1 54 55 o i xtal2: output of the oscillator amplifier circuit. xtal1: input to the oscillator amplifier and input to the internal clock generator to clock the device from an external source, drive xtal1, while leaving xtal2 unconnected. minimum and maximum high/low and rise/fall times specified in the ac characteristics must be observed. rstin 69 i/o reset input with schmitt-trigger characteristics. a low level at this pin while the oscillator is running resets the c164ci. an internal pullup resistor permits power-on reset using only a capacitor connected to v ss . a spike filter suppresses input pulses <10 ns. input pulses >100 ns safely pass the filter. the minimum duration for a safe recognition should be 100 ns + 2 cpu clock cycles. in bidirectional reset mode (enabled by setting bit bdrsten in register syscon) the rstin line is internally pulled low for the duration of the internal reset sequence upon any reset (hw, sw, wdt). see note below this table. rst out 70 o internal reset indication output. this pin is set to a low level when the part is executing either a hardware-, a software- or a watchdog timer reset. rstout remains low until the einit (end of initialization) instruction is executed. nmi 71 i non-maskable interrupt input. a high to low transition at this pin causes the cpu to vector to the nmi trap routine. when the pwrdn (power down) instruction is executed, the nmi pin must be low in order to force the c164ci to go into power down mode. if nmi is high, when pwrdn is executed, the part will continue to run in normal mode. if not used, pin nmi should be pulled high externally. table 2 pin definitions and functions (cont ? d) symbol pin no. input outp. function
c164ci/si c164cl/sl data sheet 10 v2.0, 2001-05 note: the following behavioural differences must be observed when the bidirectional reset is active: bit bdrsten in register syscon cannot be changed after einit and is cleared automatically after a reset. the reset indication flags always indicate a long hardware reset. the port0 configuration is treated as if it were a hardware reset. in particular, the bootstrap loader may be activated when p0l.4 is low. pin rstin may only be connected to external reset devices with an open drain output driver. a short hardware reset is extended to the duration of the internal reset sequence. p8 p8.0 p8.1 p8.2 p8.3 72 73 74 75 io i/o i i/o o i/o i i/o o port 8 is a 4-bit bidirectional i/o port. it is bit-wise programmable for input or output via direction bits. for a pin configured as input, the output driver is put into high- impedance state. port 8 outputs can be configured as push/ pull or open drain drivers. the input threshold of port 8 is selectable (ttl or special). port 8 pins provide inputs/ outputs for capcom2 and serial interface lines. 1) cc16io capcom2: cc16 capture inp./compare outp., can1_rxd can 1 receive data input cc17io capcom2: cc17 capture inp./compare outp., can1_txd can 1 transmit data output cc18io capcom2: cc18 capture inp./compare outp., can1_rxd can 1 receive data input cc19io capcom2: cc19 capture inp./compare outp., can1_txd can 1 transmit data output v aref 1 ? reference voltage for the a/d converter. v agnd 80 ? reference ground for the a/d converter. v dd 7, 21, 40, 53, 61 ? digital supply voltage: +5 v during normal operation and idle mode. 2.5 v during power down mode. v ss 6, 20, 41, 56, 60 ? digital ground. 1) the can interface lines are assigned to ports p4 and p8 under software control. within the can module several assignments can be selected. table 2 pin definitions and functions (cont ? d) symbol pin no. input outp. function
c164ci/si c164cl/sl data sheet 11 v2.0, 2001-05 functional description the architecture of the c164ci combines advantages of both risc and cisc processors and of advanced peripheral subsystems in a very well-balanced way. in addition the on-chip memory blocks allow the design of compact systems with maximum performance. the following block diagram gives an overview of the different on-chip components and of the advanced, high bandwidth internal bus structure of the c164ci. note: all time specifications refer to a cpu clock of 25 mhz (see definition in the ac characteristics section). figure 3 block diagram the program memory, the internal ram (iram) and the set of generic peripherals are connected to the cpu via separate buses. a fourth bus, the xbus, connects external resources as well as additional on-chip resoures, the x-peripherals (see figure 3 ). the xbus resources (xram, can) of the c164ci can be enabled or disabled during initialization by setting the general x-peripheral enable bit xpen (syscon.2). modules that are disabled consume neither address space nor port pins. c166-core cpu interrupt bus xtal mcb04323_4ci osc / pll rtc wdt 32 16 interrupt controller 16-level priority pec external instr. / data gpt1 t2 t3 t4 ssc brgen (spi) asc0 brgen (usart) adc 10-bit 8 channels ccom2 t7 t8 ccom6 t12 t13 ebc xbus control external bus control iram d u a l p o rt internal ram 2 kbyte progmem rom: 48/64 otp: 64 kbyte data data 16 16 16 can rev 2.0b active instr. / data port 0 xram 2 kbyte 6 p o rt 1 16 8 port 5 port 3 9 4 port 8 p o rt 4 o n -c h ip x b u s (1 6 -b it d e m u x ) peripheral data bus 16 16
c164ci/si c164cl/sl data sheet 12 v2.0, 2001-05 memory organization the memory space of the c164ci is configured in a von neumann architecture which means that code memory, data memory, registers and i/o ports are organized within the same linear address space which includes 16 mbytes. the entire memory space can be accessed bytewise or wordwise. particular portions of the on-chip memory have additionally been made directly bitaddressable. the c164ci incorporates 64 kbytes of on-chip otp memory or 64/48 kbytes of on-chip mask-programmable rom (not in the rom-less derivative, of course) for code or constant data. the lower 32 kbytes of the on-chip rom/otp can be mapped either to segment 0 or segment 1. the otp memory can be programmed by the cpu itself (in system, e.g. during booting) or directly via an external interface (e.g. before assembly). the programming time is approx. 100 s per word. an external programming voltage v pp =11.5v must be supplied for this purpose (via pin ea / v pp ). 2 kbytes of on-chip internal ram (iram) are provided as a storage for user defined variables, for the system stack, general purpose register banks and even for code. a register bank can consist of up to 16 wordwide (r0 to r15) and/or bytewide (rl0, rh0, ? , rl7, rh7) so-called general purpose registers (gprs). 1024 bytes (2 512 bytes) of the address space are reserved for the special function register areas (sfr space and esfr space). sfrs are wordwide registers which are used for controlling and monitoring functions of the different on-chip units. unused sfr addresses are reserved for future members of the c166 family. 2 kbytes of on-chip extension ram (xram) are provided to store user data, user stacks, or code. the xram is accessed like external memory and therefore cannot be used for the system stack or for register banks and is not bitaddressable. the xram permits 16-bit accesses with maximum speed. in order to meet the needs of designs where more memory is required than is provided on chip, up to 4 mbytes of external ram and/or rom can be connected to the microcontroller.
c164ci/si c164cl/sl data sheet 13 v2.0, 2001-05 external bus controller all of the external memory accesses are performed by a particular on-chip external bus controller (ebc). it can be programmed either to single chip mode when no external memory is required, or to one of four different external memory access modes, which are as follows: ? 16-/18-/20-/22-bit addresses, 16-bit data, demultiplexed ? 16-/18-/20-/22-bit addresses, 16-bit data, multiplexed ? 16-/18-/20-/22-bit addresses, 8-bit data, multiplexed ? 16-/18-/20-/22-bit addresses, 8-bit data, demultiplexed in the demultiplexed bus modes, addresses are output on port1 and data is input/ output on port0 or p0l, respectively. in the multiplexed bus modes both addresses and data use port0 for input/output. important timing characteristics of the external bus interface (memory cycle time, memory tri-state time, length of ale and read write delay) have been made programmable to allow the user the adaption of a wide range of different types of memories and external peripherals. in addition, up to 4 independent address windows may be defined (via register pairs addrselx / busconx) which control the access to different resources with different bus characteristics. these address windows are arranged hierarchically where buscon4 overrides buscon3 and buscon2 overrides buscon1. all accesses to locations not covered by these 4 address windows are controlled by buscon0. up to 4 external cs signals (3 windows plus default) can be generated in order to save external glue logic. the c164ci offers the possibility to switch the cs outputs to an unlatched mode. in this mode the internal filter logic is switched off and the cs signals are directly generated from the address. the unlatched cs mode is enabled by setting cscfg (syscon.6). for applications which require less than 4 mbytes of external memory space, this address space can be restricted to 1 mbyte, 256 kbyte, or to 64 kbyte. in this case port 4 outputs four, two, or no address lines at all. it outputs all 6 address lines, if an address space of 4 mbytes is used. note: when the on-chip can module is used with the interface lines assigned to port 4, the can lines override the segment address lines and the segment address output on port 4 is therefore limited to 4 bits i.e. address lines a19 ? a16.
c164ci/si c164cl/sl data sheet 14 v2.0, 2001-05 central processing unit (cpu) the main core of the cpu consists of a 4-stage instruction pipeline, a 16-bit arithmetic and logic unit (alu) and dedicated sfrs. additional hardware has been spent for a separate multiply and divide unit, a bit-mask generator and a barrel shifter. based on these hardware provisions, most of the c164ci ? s instructions can be executed in just one machine cycle which requires 2 cpu clocks (4 tcl). for example, shift and rotate instructions are always processed during one machine cycle independent of the number of bits to be shifted. all multiple-cycle instructions have been optimized so that they can be executed very fast as well: branches in 2 cycles, a 16 16 bit multiplication in 5 cycles and a 32-/16-bit division in 10 cycles. another pipeline optimization, the so- called ? jump cache ? , reduces the execution time of repeatedly performed jumps in a loop from 2 cycles to 1 cycle. figure 4 cpu block diagram mcb02147 cpu sp stkov stkun instr. reg. instr. ptr. exec. unit 4-stage pipeline mdh mdl psw syscon context ptr. mul/div-hw r15 r0 general purpose registers bit-mask gen barrel - shifter alu (16-bit) data page ptr. code seg. ptr. internal ram r15 r0 rom 16 16 32 buscon 0 buscon 1 buscon 2 buscon 3 buscon 4 addrsel 4 addrsel 3 addrsel 2 addrsel 1
c164ci/si c164cl/sl data sheet 15 v2.0, 2001-05 the cpu has a register context consisting of up to 16 wordwide gprs at its disposal. these 16 gprs are physically allocated within the on-chip ram area. a context pointer (cp) register determines the base address of the active register bank to be accessed by the cpu at any time. the number of register banks is only restricted by the available internal ram space. for easy parameter passing, a register bank may overlap others. a system stack of up to 1024 words is provided as a storage for temporary data. the system stack is allocated in the on-chip ram area, and it is accessed by the cpu via the stack pointer (sp) register. two separate sfrs, stkov and stkun, are implicitly compared against the stack pointer value upon each stack access for the detection of a stack overflow or underflow. the high performance offered by the hardware implementation of the cpu can efficiently be utilized by a programmer via the highly efficient c164ci instruction set which includes the following instruction classes: ? arithmetic instructions ? logical instructions ? boolean bit manipulation instructions ? compare and loop control instructions ? shift and rotate instructions ? prioritize instruction ? data movement instructions ? system stack instructions ? jump and call instructions ? return instructions ? system control instructions ? miscellaneous instructions the basic instruction length is either 2 or 4 bytes. possible operand types are bits, bytes and words. a variety of direct, indirect or immediate addressing modes are provided to specify the required operands.
c164ci/si c164cl/sl data sheet 16 v2.0, 2001-05 interrupt system with an interrupt response time within a range from just 5 to 12 cpu clocks (in case of internal program execution), the c164ci is capable of reacting very fast to the occurrence of non-deterministic events. the architecture of the c164ci supports several mechanisms for fast and flexible response to service requests that can be generated from various sources internal or external to the microcontroller. any of these interrupt requests can be programmed to being serviced by the interrupt controller or by the peripheral event controller (pec). in contrast to a standard interrupt service where the current program execution is suspended and a branch to the interrupt vector table is performed, just one cycle is ? stolen ? from the current cpu activity to perform a pec service. a pec service implies a single byte or word data transfer between any two memory locations with an additional increment of either the pec source or the destination pointer. an individual pec transfer counter is implicity decremented for each pec service except when performing in the continuous transfer mode. when this counter reaches zero, a standard interrupt is performed to the corresponding source related vector location. pec services are very well suited, for example, for supporting the transmission or reception of blocks of data. the c164ci has 8 pec channels each of which offers such fast interrupt-driven data transfer capabilities. a separate control register which contains an interrupt request flag, an interrupt enable flag and an interrupt priority bitfield exists for each of the possible interrupt sources. via its related register, each source can be programmed to one of sixteen interrupt priority levels. once having been accepted by the cpu, an interrupt service can only be interrupted by a higher prioritized service request. for the standard interrupt processing, each of the possible interrupt sources has a dedicated vector location. fast external interrupt inputs are provided to service external interrupts with high precision requirements. these fast interrupt inputs feature programmable edge detection (rising edge, falling edge or both edges). software interrupts are supported by means of the ? trap ? instruction in combination with an individual trap (interrupt) number. table 3 shows all of the possible c164ci interrupt sources and the corresponding hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers. note: interrupt nodes which are not used by associated peripherals, may be used to generate software controlled interrupt requests by setting the respective interrupt request bit (xir).
c164ci/si c164cl/sl data sheet 17 v2.0, 2001-05 table 3 c164ci interrupt nodes source of interrupt or pec service request request flag enable flag interrupt vector vector location trap number fast external interrupt 0 cc8ir cc8ie cc8int 00 ? 0060 h 18 h fast external interrupt 1 cc9ir cc9ie cc9int 00 ? 0064 h 19 h fast external interrupt 2 cc10ir cc10ie cc10int 00 ? 0068 h 1a h fast external interrupt 3 cc11ir cc11ie cc11int 00 ? 006c h 1b h gpt1 timer 2 t2ir t2ie t2int 00 ? 0088 h 22 h gpt1 timer 3 t3ir t3ie t3int 00 ? 008c h 23 h gpt1 timer 4 t4ir t4ie t4int 00 ? 0090 h 24 h a/d conversion complete adcir adcie adcint 00 ? 00a0 h 28 h a/d overrun error adeir adeie adeint 00 ? 00a4 h 29 h asc0 transmit s0tir s0tie s0tint 00 ? 00a8 h 2a h asc0 transmit buffer s0tbir s0tbie s0tbint 00 ? 011c h 47 h asc0 receive s0rir s0rie s0rint 00 ? 00ac h 2b h asc0 error s0eir s0eie s0eint 00 ? 00b0 h 2c h ssc transmit sctir sctie sctint 00 ? 00b4 h 2d h ssc receive scrir scrie scrint 00 ? 00b8 h 2e h ssc error sceir sceie sceint 00 ? 00bc h 2f h capcom register 16 cc16ir cc16ie cc16int 00 ? 00c0 h 30 h capcom register 17 cc17ir cc17ie cc17int 00 ? 00c4 h 31 h capcom register 18 cc18ir cc18ie cc18int 00 ? 00c8 h 32 h capcom register 19 cc19ir cc19ie cc19int 00 ? 00cc h 33 h capcom register 24 cc24ir cc24ie cc24int 00 ? 00e0 h 38 h capcom register 25 cc25ir cc25ie cc25int 00 ? 00e4 h 39 h capcom register 26 cc26ir cc26ie cc26int 00 ? 00e8 h 3a h capcom register 27 cc27ir cc27ie cc27int 00 ? 00ec h 3b h capcom timer 7 t7ir t7ie t7int 00 ? 00f4 h 3d h capcom timer 8 t8ir t8ie t8int 00 ? 00f8 h 3e h capcom6 interrupt cc6ir cc6ie cc6int 00 ? 00fc h 3f h can interface 1 xp0ir xp0ie xp0int 00 ? 0100 h 40 h pll/owd and rtc xp3ir xp3ie xp3int 00 ? 010c h 43 h
c164ci/si c164cl/sl data sheet 18 v2.0, 2001-05 capcom 6 timer 12 t12ir t12ie t12int 00 ? 0134 h 4d h capcom 6 timer 13 t13ir t13ie t13int 00 ? 0138 h 4e h capcom 6 emergency cc6eir cc6eie cc6eint 00 ? 013c h 4f h table 3 c164ci interrupt nodes (cont ? d) source of interrupt or pec service request request flag enable flag interrupt vector vector location trap number
c164ci/si c164cl/sl data sheet 19 v2.0, 2001-05 the c164ci also provides an excellent mechanism to identify and to process exceptions or error conditions that arise during run-time, so-called ? hardware traps ? . hardware traps cause immediate non-maskable system reaction which is similar to a standard interrupt service (branching to a dedicated vector table location). the occurence of a hardware trap is additionally signified by an individual bit in the trap flag register (tfr). except when another higher prioritized trap service is in progress, a hardware trap will interrupt any actual program execution. in turn, hardware trap services can normally not be interrupted by standard or pec interrupts. table 4 shows all of the possible exceptions or error conditions that can arise during run- time: table 4 hardware trap summary exception condition trap flag trap vector vector location trap number trap priority reset functions: ? hardware reset ? software reset ? w-dog timer overflow ? reset reset reset 00 ? 0000 h 00 ? 0000 h 00 ? 0000 h 00 h 00 h 00 h iii iii iii class a hardware traps: ? non-maskable interrupt ? stack overflow ? stack underflow nmi stkof stkuf nmitrap stotrap stutrap 00 ? 0008 h 00 ? 0010 h 00 ? 0018 h 02 h 04 h 06 h ii ii ii class b hardware traps: ? undefined opcode ? protected instruction fault ? illegal word operand access ? illegal instruction access ? illegal external bus access undopc prtflt illopa illina illbus btrap btrap btrap btrap btrap 00 ? 0028 h 00 ? 0028 h 00 ? 0028 h 00 ? 0028 h 00 ? 0028 h 0a h 0a h 0a h 0a h 0a h i i i i i reserved ?? [2c h ? 3c h ] [0b h ? 0f h ] ? software traps ? trap instruction ?? any [00 ? 0000 h ? 00 ? 01fc h ] in steps of 4 h any [00 h ? 7f h ] current cpu priority
c164ci/si c164cl/sl data sheet 20 v2.0, 2001-05 the capture/compare unit capcom2 the general purpose capcom2 unit supports generation and control of timing sequences on up to 8 channels with a maximum resolution of 16 tcl. the capcom units are typically used to handle high speed i/o tasks such as pulse and waveform generation, pulse width modulation (pmw), digital to analog (d/a) conversion, software timing, or time recording relative to external events. two 16-bit timers (t7/t8) with reload registers provide two independent time bases for the capture/compare register array. each dual purpose capture/compare register, which may be individually allocated to either capcom timer and programmed for capture or compare function, has one port pin associated with it which serves as an input pin for triggering the capture function, or as an output pin to indicate the occurrence of a compare event. when a capture/compare register has been selected for capture mode, the current contents of the allocated timer will be latched ( ? capture ? d) into the capture/compare register in response to an external event at the port pin which is associated with this register. in addition, a specific interrupt request for this capture/compare register is generated. either a positive, a negative, or both a positive and a negative external signal transition at the pin can be selected as the triggering event. the contents of all registers which have been selected for one of the five compare modes are continuously compared with the contents of the allocated timers. when a match occurs between the timer value and the value in a capture/compare register, specific actions will be taken based on the selected compare mode. table 5 compare modes (capcom2) compare modes function mode 0 interrupt-only compare mode; several compare interrupts per timer period are possible mode 1 pin toggles on each compare match; several compare events per timer period are possible mode 2 interrupt-only compare mode; only one compare interrupt per timer period is generated mode 3 pin set ? 1 ? on match; pin reset ? 0 ? on compare time overflow; only one compare event per timer period is generated double register mode two registers operate on one pin; pin toggles on each compare match; several compare events per timer period are possible. registers cc16 & cc24 pin cc16io registers cc17 & cc25 pin cc17io registers cc18 & cc26 pin cc18io registers cc19 & cc27 pin cc19io
c164ci/si c164cl/sl data sheet 21 v2.0, 2001-05 the capture/compare unit capcom6 the capcom6 unit supports generation and control of timing sequences on up to three 16-bit capture/compare channels plus one 10-bit compare channel. in compare mode the capcom6 unit provides two output signals per channel which have inverted polarity and non-overlapping pulse transitions. the compare channel can generate a single pwm output signal and is further used to modulate the capture/ compare output signals. in capture mode the contents of compare timer 12 is stored in the capture registers upon a signal transition at pins ccx. compare timers t12 (16-bit) and t13 (10-bit) are free running timers which are clocked by the prescaled cpu clock. figure 5 capcom6 block diagram for motor control applications both subunits may generate versatile multichannel pwm signals which are basically either controlled by compare timer 12 or by a typical hall sensor pattern at the interrupt inputs (block commutation). note: multichannel signal generation is provided only in devices with a full capcom6. control cc channel 0 cc60 cc channel 1 cc61 cc channel 2 cc62 mcb04109 prescaler offset register t12of compare timer t12 16-bit period register t12p mode select register cc6msel trap register port control logic control register ctcon compare register cmp13 prescaler compare timer t13 10-bit period register t13p block commutation control cc6mcon.h cc60 cout60 cc61 cout61 cc62 cout62 ctrap cc6pos0 cc6pos1 cc6pos2 f cpu f cpu cout63 the timer registers (t12, t13) are not directly accessible. the period and offset registers are loading a value into the timer registers. the shaded blocks are available in the full function module only.
c164ci/si c164cl/sl data sheet 22 v2.0, 2001-05 general purpose timer (gpt) unit the gpt unit represents a very flexible multifunctional timer/counter structure which may be used for many different time related tasks such as event timing and counting, pulse width and duty cycle measurements, pulse generation, or pulse multiplication. the gpt unit incorporates three 16-bit timers. each timer may operate independently in a number of different modes, or may be concatenated with another timer. each of the three timers t2, t3, t4 of module gpt1 can be configured individually for one of four basic modes of operation, which are timer, gated timer, counter, and incremental interface mode. in timer mode, the input clock for a timer is derived from the cpu clock, divided by a programmable prescaler, while counter mode allows a timer to be clocked in reference to external events. pulse width or duty cycle measurement is supported in gated timer mode, where the operation of a timer is controlled by the ? gate ? level on an external input pin. for these purposes, each timer has one associated port pin (txin) which serves as gate or clock input. the maximum resolution of the timers in module gpt1 is 16 tcl. the count direction (up/down) for each timer is programmable by software or may additionally be altered dynamically by an external signal on a port pin (txeud) to facilitate e.g. position tracking. in incremental interface mode the gpt1 timers (t2, t3, t4) can be directly connected to the incremental position sensor signals a and b via their respective inputs txin and txeud. direction and count signals are internally derived from these two input signals, so the contents of the respective timer tx corresponds to the sensor position. the third position sensor signal top0 can be connected to an interrupt input. timer t3 has an output toggle latch (t3otl) which changes its state on each timer over- flow/underflow. the state of this latch may be used internally to clock timers t2 and t4 for measuring long time periods with high resolution. in addition to their basic operating modes, timers t2 and t4 may be configured as reload or capture registers for timer t3. when used as capture or reload registers, timers t2 and t4 are stopped. the contents of timer t3 is captured into t2 or t4 in response to a signal at their associated input pins (txin). timer t3 is reloaded with the contents of t2 or t4 triggered either by an external signal or by a selectable state transition of its toggle latch t3otl.
c164ci/si c164cl/sl data sheet 23 v2.0, 2001-05 figure 6 block diagram of gpt1 t3 mode control 2 n : 1 f cpu 2 n : 1 f cpu t2 mode control gpt1 timer t2 reload capture 2 n : 1 f cpu t4 mode control gpt1 timer t4 reload capture gpt1 timer t3 t3otl u/d t2eud t2in t3in t3eud t4in t4eud toggle ff u/d u/d interrupt request (t2ir) interrupt request (t3ir) interrupt request (t4ir) other timers mct04825_4.vsd n = 3 ? 10
c164ci/si c164cl/sl data sheet 24 v2.0, 2001-05 real time clock the real time clock (rtc) module of the c164ci consists of a chain of 3 divider blocks, a fixed 8:1 divider, the reloadable 16-bit timer t14, and the 32-bit rtc timer (accessible via registers rtch and rtcl). the rtc module is directly clocked with the on-chip oscillator frequency divided by 32 via a separate clock driver ( f rtc = f osc /32) and is therefore independent from the selected clock generation mode of the c164ci. all timers count up. the rtc module can be used for different purposes: system clock to determine the current time and date cyclic time based interrupt 48-bit timer for long term measurements figure 7 rtc block diagram note: the registers associated with the rtc are not affected by a reset in order to maintain the correct system time even when intermediate resets are executed. mcd04432 t14rel t14 8:1 rtc f rtcl rtch interrupt request reload
c164ci/si c164cl/sl data sheet 25 v2.0, 2001-05 a/d converter for analog signal measurement, a 10-bit a/d converter with 8 multiplexed input channels and a sample and hold circuit has been integrated on-chip. it uses the method of successive approximation. the sample time (for loading the capacitors) and the conversion time is programmable and can so be adjusted to the external circuitry. overrun error detection/protection is provided for the conversion result register (addat): either an interrupt request will be generated when the result of a previous conversion has not been read from the result register at the time the next conversion is complete, or the next conversion is suspended in such a case until the previous result has been read. for applications which require less than 8 analog input channels, the remaining channel inputs can be used as digital input port pins. the a/d converter of the c164ci supports four different conversion modes. in the standard single channel conversion mode, the analog level on a specified channel is sampled once and converted to a digital result. in the single channel continuous mode, the analog level on a specified channel is repeatedly sampled and converted without software intervention. in the auto scan mode, the analog levels on a prespecified number of channels (standard or extension) are sequentially sampled and converted. in the auto scan continuous mode, the number of prespecified channels is repeatedly sampled and converted. in addition, the conversion of a specific channel can be inserted (injected) into a running sequence without disturbing this sequence. this is called channel injection mode. the peripheral event controller (pec) may be used to automatically store the conversion results into a table in memory for later evaluation, without requiring the overhead of entering and exiting interrupt routines for each data transfer. after each reset and also during normal operation the adc automatically performs calibration cycles. this automatic self-calibration constantly adjusts the converter to changing operating conditions (e.g. temperature) and compensates process variations. these calibration cycles are part of the conversion cycle, so they do not affect the normal operation of the a/d converter. in order to decouple analog inputs from digital noise and to avoid input trigger noise those pins used for analog input can be disconnected from the digital io or input stages under software control. this can be selected for each pin separately via register p5didis (port 5 digital input disable).
c164ci/si c164cl/sl data sheet 26 v2.0, 2001-05 serial channels serial communication with other microcontrollers, processors, terminals or external peripheral components is provided by two serial interfaces with different functionality, an asynchronous/synchronous serial channel ( asc0 ) and a high-speed synchronous serial channel ( ssc ). the asc0 is upward compatible with the serial ports of the infineon 8-bit microcontroller families and supports full-duplex asynchronous communication at up to 781 kbit/s and half-duplex synchronous communication at up to 3.1 mbit/s (@ 25 mhz cpu clock). a dedicated baud rate generator allows to set up all standard baud rates without oscillator tuning. for transmission, reception and error handling 4 separate interrupt vectors are provided. in asynchronous mode, 8- or 9-bit data frames are transmitted or received, preceded by a start bit and terminated by one or two stop bits. for multiprocessor communication, a mechanism to distinguish address from data bytes has been included (8-bit data plus wake up bit mode). in synchronous mode, the asc0 transmits or receives bytes (8 bits) synchronously to a shift clock which is generated by the asc0. the asc0 always shifts the lsb first. a loop back option is available for testing purposes. a number of optional hardware error detection capabilities has been included to increase the reliability of data transfers. a parity bit can automatically be generated on transmission or be checked on reception. framing error detection allows to recognize data frames with missing stop bits. an overrun error will be generated, if the last character received has not been read out of the receive buffer register at the time the reception of a new character is complete. the ssc supports full-duplex synchronous communication at up to 6.25 mbit/s (@ 25 mhz cpu clock). it may be configured so it interfaces with serially linked peripheral components. a dedicated baud rate generator allows to set up all standard baud rates without oscillator tuning. for transmission, reception and error handling 3 separate interrupt vectors are provided. the ssc transmits or receives characters of 2 ? 16 bits length synchronously to a shift clock which can be generated by the ssc (master mode) or by an external master (slave mode). the ssc can start shifting with the lsb or with the msb and allows the selection of shifting and latching clock edges as well as the clock polarity. a number of optional hardware error detection capabilities has been included to increase the reliability of data transfers. transmit and receive error supervise the correct handling of the data buffer. phase and baudrate error detect incorrect serial data.
c164ci/si c164cl/sl data sheet 27 v2.0, 2001-05 can-module the integrated can-module handles the completely autonomous transmission and reception of can frames in accordance with the can specification v2.0 part b (active), i.e. the on-chip can-modules can receive and transmit standard frames with 11-bit identifiers as well as extended frames with 29-bit identifiers. the module provides full can functionality on up to 15 message objects. message object 15 may be configured for basic can functionality. both modes provide separate masks for acceptance filtering which allows to accept a number of identifiers in full can mode and also allows to disregard a number of identifiers in basic can mode. all message objects can be updated independent from the other objects and are equipped for the maximum message length of 8 bytes. the bit timing is derived from the xclk and is programmable up to a data rate of 1 mbit/ s. each can-module uses two pins of port 4 or port 8 to interface to an external bus transceiver. the interface pins are assigned via software. note: when the can interface is assigned to port 4, the respective segment address lines on port 4 cannot be used. this will limit the external address space. watchdog timer the watchdog timer represents one of the fail-safe mechanisms which have been implemented to prevent the controller from malfunctioning for longer periods of time. the watchdog timer is always enabled after a reset of the chip, and can only be disabled in the time interval until the einit (end of initialization) instruction has been executed. thus, the chip ? s start-up procedure is always monitored. the software has to be designed to service the watchdog timer before it overflows. if, due to hardware or software related failures, the software fails to do so, the watchdog timer overflows and generates an internal hardware reset and pulls the rstout pin low in order to allow external hardware components to be reset. the watchdog timer is a 16-bit timer, clocked with the system clock divided by 2/4/128/ 256. the high byte of the watchdog timer register can be set to a prespecified reload value (stored in wdtrel) in order to allow further variation of the monitored time interval. each time it is serviced by the application software, the high byte of the watchdog timer is reloaded. thus, time intervals between 20 s and 336 ms can be monitored (@ 25 mhz). the default watchdog timer interval after reset is 5.24 ms (@ 25 mhz).
c164ci/si c164cl/sl data sheet 28 v2.0, 2001-05 parallel ports the c164ci provides up to 59 i/o lines which are organized into five input/output ports and one input port. all port lines are bit-addressable, and all input/output lines are individually (bit-wise) programmable as inputs or outputs via direction registers. the i/o ports are true bidirectional ports which are switched to high impedance state when configured as inputs. the output drivers of three i/o ports can be configured (pin by pin) for push/pull operation or open-drain operation via control registers. during the internal reset, all port pins are configured as inputs. the input threshold of port 3, port 4, and port 8 is selectable (ttl or cmos like), where the special cmos like input threshold reduces noise sensitivity due to the input hysteresis. the input threshold may be selected individually for each byte of the respective ports. all port lines have programmable alternate input or output functions associated with them. all port lines that are not used for these alternate functions may be used as general purpose io lines. port0 and port1 may be used as address and data lines when accessing external memory, while port 4 outputs the additional segment address bits a21/19/17 ? a16 and the optional chip select signals in systems where segmentation is enabled to access more than 64 kbytes of memory. ports p1l, p1h, and p8 are associated with the capture inputs or compare outputs of the capcom units and/or serve as external interrupt inputs. port 3 includes alternate functions of timers, serial interfaces, the optional bus control signal bhe /wrh , and the system clock output clkout (or the programmable frequency output fout). port 5 is used for the analog input channels to the a/d converter or timer control signals. the edge characteristics (transition time) and driver characteristics (output current) of the c164ci ? s port drivers can be selected via the port output control registers (poconx).
c164ci/si c164cl/sl data sheet 29 v2.0, 2001-05 oscillator watchdog the oscillator watchdog (owd) monitors the clock signal generated by the on-chip oscillator (either with a crystal or via external clock drive). for this operation the pll provides a clock signal which is used to supervise transitions on the oscillator clock. this pll clock is independent from the xtal1 clock. when the expected oscillator clock transitions are missing the owd activates the pll unlock/owd interrupt node and supplies the cpu with the pll clock signal. under these circumstances the pll will oscillate with its basic frequency. in direct drive mode the pll base frequency is used directly ( f cpu = 2 ? 5 mhz). in prescaler mode the pll base frequency is divided by 2 ( f cpu = 1 ? 2.5 mhz). note: the cpu clock source is only switched back to the oscillator clock after a hardware reset. the oscillator watchdog can be disabled by setting bit owddis in register syscon. in this case (owddis = ? 1 ? ) the pll remains idle and provides no clock signal, while the cpu clock signal is derived directly from the oscillator clock or via prescaler or sdd. also no interrupt request will be generated in case of a missing oscillator clock. note: at the end of a reset bit owddis reflects the inverted level of pin rd at that time. thus the oscillator watchdog may also be disabled via hardware by (externally) pulling the rd line low upon a reset, similar to the standard reset configuration via port0.
c164ci/si c164cl/sl data sheet 30 v2.0, 2001-05 power management the c164ci provides several means to control the power it consumes either at a given time or averaged over a certain timespan. three mechanisms can be used (partly in parallel): power saving modes switch the c164ci into a special operating mode (control via instructions). idle mode stops the cpu while the peripherals can continue to operate. sleep mode and power down mode stop all clock signals and all operation (rtc may optionally continue running). sleep mode can be terminated by external interrupt signals. clock generation management controls the distribution and the frequency of internal and external clock signals (control via register syscon2). slow down mode lets the c164ci run at a cpu clock frequency of f osc /1 ? 32 (half for prescaler operation) which drastically reduces the consumed power. the pll can be optionally disabled while operating in slow down mode. external circuitry can be controlled via the programmable frequency output fout. peripheral management permits temporary disabling of peripheral modules (control via register syscon3). each peripheral can separately be disabled/enabled. a group control option disables a major part of the peripheral set by setting one single bit. the on-chip rtc supports intermittend operation of the c164ci by generating cyclic wakeup signals. this offers full performance to quickly react on action requests while the intermittend sleep phases greatly reduce the average power consumption of the system.
c164ci/si c164cl/sl data sheet 31 v2.0, 2001-05 instruction set summary table 6 lists the instructions of the c164ci in a condensed way. the various addressing modes that can be used with a specific instruction, the operation of the instructions, parameters for conditional execution of instructions, and the opcodes for each instruction can be found in the ? c166 family instruction set manual ? . this document also provides a detailled description of each instruction. table 6 instruction set summary mnemonic description bytes add(b) add word (byte) operands 2 / 4 addc(b) add word (byte) operands with carry 2 / 4 sub(b) subtract word (byte) operands 2 / 4 subc(b) subtract word (byte) operands with carry 2 / 4 mul(u) (un)signed multiply direct gpr by direct gpr (16-16-bit) 2 div(u) (un)signed divide register mdl by direct gpr (16-/16-bit) 2 divl(u) (un)signed long divide reg. md by direct gpr (32-/16-bit) 2 cpl(b) complement direct word (byte) gpr 2 neg(b) negate direct word (byte) gpr 2 and(b) bitwise and, (word/byte operands) 2 / 4 or(b) bitwise or, (word/byte operands) 2 / 4 xor(b) bitwise xor, (word/byte operands) 2 / 4 bclr clear direct bit 2 bset set direct bit 2 bmov(n) move (negated) direct bit to direct bit 4 band, bor, bxor and/or/xor direct bit with direct bit 4 bcmp compare direct bit to direct bit 4 bfldh/l bitwise modify masked high/low byte of bit-addressable direct word memory with immediate data 4 cmp(b) compare word (byte) operands 2 / 4 cmpd1/2 compare word data to gpr and decrement gpr by 1/2 2 / 4 cmpi1/2 compare word data to gpr and increment gpr by 1/2 2 / 4 prior determine number of shift cycles to normalize direct word gpr and store result in direct word gpr 2 shl / shr shift left/right direct word gpr 2 rol / ror rotate left/right direct word gpr 2 ashr arithmetic (sign bit) shift right direct word gpr 2
c164ci/si c164cl/sl data sheet 32 v2.0, 2001-05 mov(b) move word (byte) data 2 / 4 movbs move byte operand to word operand with sign extension 2 / 4 movbz 2 / 4 jmpa, jmpi, jmpr jump absolute/indirect/relative if condition is met 4 jmps jump absolute to a code segment 4 j(n)b jump relative if direct bit is (not) set 4 jbc jump relative and clear bit if direct bit is set 4 jnbs jump relative and set bit if direct bit is not set 4 calla, calli, callr call absolute/indirect/relative subroutine if condition is met 4 calls call absolute subroutine in any code segment 4 pcall push direct word register onto system stack and call absolute subroutine 4 trap call interrupt service routine via immediate trap number 2 push, pop push/pop direct word register onto/from system stack 2 scxt push direct word register onto system stack und update register with word operand 4 ret return from intra-segment subroutine 2 rets return from inter-segment subroutine 2 retp return from intra-segment subroutine and pop direct word register from system stack 2 reti return from interrupt service subroutine 2 srst software reset 4 idle enter idle mode 4 pwrdn enter power down mode (supposes nmi -pin being low) 4 srvwdt service watchdog timer 4 diswdt disable watchdog timer 4 einit signify end-of-initialization on rstout -pin 4 atomic begin atomic sequence 2 extr begin extended register sequence 2 extp(r) begin extended page (and register) sequence 2 / 4 exts(r) begin extended segment (and register) sequence 2 / 4 nop null operation 2 table 6 instruction set summary (cont?d) mnemonic description bytes move byte operand to word operand with zero extension
c164ci/si c164cl/sl data sheet 33 v2.0, 2001-05 special function registers overview table 7 lists all sfrs which are implemented in the c164ci in alphabetical order. bit-addressable sfrs are marked with the letter ? b ? in column ? name ? . sfrs within the extended sfr-space (esfrs) are marked with the letter ? e ? in column ? physical address ? . registers within on-chip x-peripherals are marked with the letter ? x ? in column ? physical address ? . an sfr can be specified via its individual mnemonic name. depending on the selected addressing mode, an sfr can be accessed via its physical address (using the data page pointers), or via its short 8-bit address (without using the data page pointers). table 7 c164ci registers, ordered by name name physical address 8-bit addr. description reset value adcic b ff98 h cc h a/d converter end of conversion interrupt control register 0000 h adcon b ffa0 h d0 h a/d converter control register 0000 h addat fea0 h 50 h a/d converter result register 0000 h addat2 f0a0 h e 50 h a/d converter 2 result register 0000 h addrsel1 fe18 h 0c h address select register 1 0000 h addrsel2 fe1a h 0d h address select register 2 0000 h addrsel3 fe1c h 0e h address select register 3 0000 h addrsel4 fe1e h 0f h address select register 4 0000 h adeic b ff9a h cd h a/d converter overrun error interrupt control register 0000 h buscon0 b ff0c h 86 h bus configuration register 0 0000 h buscon1 b ff14 h 8a h bus configuration register 1 0000 h buscon2 b ff16 h 8b h bus configuration register 2 0000 h buscon3 b ff18 h 8c h bus configuration register 3 0000 h buscon4 b ff1a h 8d h bus configuration register 4 0000 h c1btr ef04 h x --- can1 bit timing register uuuu h c1csr ef00 h x --- can1 control / status register xx01 h c1gms ef06 h x --- can1 global mask short ufuu h c1larn efn4 h x --- can lower arbitration register (msg. n) uuuu h c1lgml ef0a h x --- can lower global mask long uuuu h c1lmlm ef0e h x --- can lower mask of last message uuuu h
c164ci/si c164cl/sl data sheet 34 v2.0, 2001-05 c1mcfgn efn6 h x --- can message configuration register (msg. n ) uu h c1mcrn efn0 h x --- can message control register (msg. n ) uuuu h c1pcir ef02 h x --- can1 port control / interrupt register xxxx h c1uarn efn2 h x --- can upper arbitration register (msg. n ) uuuu h c1ugml ef08 h x --- can upper global mask long uuuu h c1umlm ef0c h x --- can upper mask of last message uuuu h cc10ic b ff8c h c6 h external interrupt 2 control register 0000 h cc11ic b ff8e h c7 h external interrupt 3 control register 0000 h cc16 fe60 h 30 h capcom register 16 0000 h cc16ic b f160 h e b0 h capcom reg. 16 interrupt ctrl. reg. 0000 h cc17 fe62 h 31 h capcom register 17 0000 h cc17ic b f162 h e b1 h capcom reg. 17 interrupt ctrl. reg. 0000 h cc18 fe64 h 32 h capcom register 18 0000 h cc18ic b f164 h e b2 h capcom reg. 18 interrupt ctrl. reg. 0000 h cc19 fe66 h 33 h capcom register 19 0000 h cc19ic b f166 h e b3 h capcom reg. 19 interrupt ctrl. reg. 0000 h cc20 fe68 h 34 h capcom register 20 0000 h cc20ic b f168 h e b4 h capcom reg. 20 interrupt ctrl. reg. 0000 h cc21 fe6a h 35 h capcom register 21 0000 h cc21ic b f16a h e b5 h capcom reg. 21 interrupt ctrl. reg. 0000 h cc22 fe6c h 36 h capcom register 22 0000 h cc22ic b f16c h e b6 h capcom reg. 22 interrupt ctrl. reg. 0000 h cc23 fe6e h 37 h capcom register 23 0000 h cc23ic b f16e h e b7 h capcom reg. 23 interrupt ctrl. reg. 0000 h cc24 fe70 h 38 h capcom register 24 0000 h cc24ic b f170 h e b8 h capcom reg. 24 interrupt ctrl. reg. 0000 h cc25 fe72 h 39 h capcom register 25 0000 h cc25ic b f172 h e b9 h capcom reg. 25 interrupt ctrl. reg. 0000 h cc26 fe74 h 3a h capcom register 26 0000 h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 35 v2.0, 2001-05 cc26ic b f174 h e ba h capcom reg. 26 interrupt ctrl. reg. 0000 h cc27 fe76 h 3b h capcom register 27 0000 h cc27ic b f176 h e bb h capcom reg. 27 interrupt ctrl. reg. 0000 h cc28 fe78 h 3c h capcom register 28 0000 h cc28ic b f178 h e bc h capcom reg. 28 interrupt ctrl. reg. 0000 h cc29 fe7a h 3d h capcom register 29 0000 h cc29ic b f184 h e c2 h capcom reg. 29 interrupt ctrl. reg. 0000 h cc30 fe7c h 3e h capcom register 30 0000 h cc30ic b f18c h e c6 h capcom reg. 30 interrupt ctrl. reg. 0000 h cc31 fe7e h 3f h capcom register 31 0000 h cc31ic b f194 h e ca h capcom reg. 31 interrupt ctrl. reg. 0000 h cc60 fe30 h 18 h capcom 6 register 0 0000 h cc61 fe32 h 19 h capcom 6 register 1 0000 h cc62 fe34 h 1a h capcom 6 register 2 0000 h cc6eic b f188 h e c4 h capcom 6 emergency interrrupt control register 0000 h cc6cic b f17e h e bf h capcom 6 interrupt control register 0000 h cc6mcon b ff32 h 99 h capcom 6 mode control register 00ff h cc6mic b ff36 h 9b h capcom 6 mode interrupt ctrl. reg. 0000 h cc6msel f036 h e 1b h capcom 6 mode select register 0000 h cc8ic b ff88 h c4 h external interrupt 0 control register 0000 h cc9ic b ff8a h c5 h external interrupt 1 control register 0000 h ccm4 b ff22 h 91 h capcom mode control register 4 0000 h ccm5 b ff24 h 92 h capcom mode control register 5 0000 h ccm6 b ff26 h 93 h capcom mode control register 6 0000 h ccm7 b ff28 h 94 h capcom mode control register 7 0000 h cmp13 fe36 h 1b h capcom 6 timer 13 compare reg. 0000 h cp fe10 h 08 h cpu context pointer register fc00 h csp fe08 h 04 h cpu code segment pointer register (8 bits, not directly writeable) 0000 h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 36 v2.0, 2001-05 ctcon b ff30 h 98 h capcom 6 compare timer ctrl. reg. 1010 h dp0h b f102 h e 81 h p0h direction control register 00 h dp0l b f100 h e 80 h p0l direction control register 00 h dp1h b f106 h e 83 h p1h direction control register 00 h dp1l b f104 h e 82 h p1l direction control register 00 h dp3 b ffc6 h e3 h port 3 direction control register 0000 h dp4 b ffca h e5 h port 4 direction control register 00 h dp8 b ffd6 h eb h port 8 direction control register 00 h dpp0 fe00 h 00 h cpu data page pointer 0 reg. (10 bits) 0000 h dpp1 fe02 h 01 h cpu data page pointer 1 reg. (10 bits) 0001 h dpp2 fe04 h 02 h cpu data page pointer 2 reg. (10 bits) 0002 h dpp3 fe06 h 03 h cpu data page pointer 3 reg. (10 bits) 0003 h exicon b f1c0 h e e0 h external interrupt control register 0000 h exisel b f1da h e ed h external interrupt source select reg. 0000 h focon b ffaa h d5 h frequency output control register 0000 h idchip f07c h e 3e h identifier xxxx h idmanuf f07e h e 3f h identifier 1820 h idmem f07a h e 3d h identifier xxxx h idprog f078 h e 3c h identifier xxxx h idmem2 f076 h e 3b h identifier xxxx h isnc b f1de h e ef h interrupt subnode control register 0000 h mdc b ff0e h 87 h cpu multiply divide control register 0000 h mdh fe0c h 06 h cpu multiply divide reg. ? high word 0000 h mdl fe0e h 07 h cpu multiply divide reg. ? low word 0000 h odp3 b f1c6 h e e3 h port 3 open drain control register 0000 h odp4 b f1ca h e e5 h port 4 open drain control register 00 h odp8 b f1d6 h e eb h port 8 open drain control register 00 h ones b ff1e h 8f h constant value 1 ? s register (read only) ffff h opad edc2 h x --- otp progr. interface address register 0000 h opctrl edc0 h x --- otp progr. interface control register 0007 h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 37 v2.0, 2001-05 opdat edc4 h x --- otp progr. interface data register 0000 h p0h b ff02 h 81 h port 0 high reg. (upper half of port0) 00 h p0l b ff00 h 80 h port 0 low reg. (lower half of port0) 00 h p1h b ff06 h 83 h port 1 high reg. (upper half of port1) 00 h p1l b ff04 h 82 h port 1 low reg. (lower half of port1) 00 h p3 b ffc4 h e2 h port 3 register 0000 h p4 b ffc8 h e4 h port 4 register (7 bits) 00 h p5 b ffa2 h d1 h port 5 register (read only) xxxx h p5didis b ffa4 h d2 h port 5 digital input disable register 0000 h p8 b ffd4 h ea h port 8 register (8 bits) 00 h pecc0 fec0 h 60 h pec channel 0 control register 0000 h pecc1 fec2 h 61 h pec channel 1 control register 0000 h pecc2 fec4 h 62 h pec channel 2 control register 0000 h pecc3 fec6 h 63 h pec channel 3 control register 0000 h pecc4 fec8 h 64 h pec channel 4 control register 0000 h pecc5 feca h 65 h pec channel 5 control register 0000 h pecc6 fecc h 66 h pec channel 6 control register 0000 h pecc7 fece h 67 h pec channel 7 control register 0000 h picon b f1c4 h e e2 h port input threshold control register 0000 h pocon0h f082 h e 41 h port p0h output control register 0011 h pocon0l f080 h e 40 h port p0l output control register 0011 h pocon1h f086 h e 43 h port p1h output control register 0011 h pocon1l f084 h e 42 h port p1l output control register 0011 h pocon20 f0aa h e 55 h dedicated pin output control register 0000 h pocon3 f08a h e 45 h port p3 output control register 2222 h pocon4 f08c h e 46 h port p4 output control register 0010 h pocon8 f092 h e 49 h port p8 output control register 0022 h psw b ff10 h 88 h cpu program status word 0000 h rp0h b f108 h e 84 h system startup config. reg. (rd. only) xx h rstcon b f1e0 h m --- reset control register 00xx h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 38 v2.0, 2001-05 rtch f0d6 h e 6b h rtc high register no rtcl f0d4 h e 6a h rtc low register no s0bg feb4 h 5a h serial channel 0 baud rate generator reload register 0000 h s0con b ffb0 h d8 h serial channel 0 control register 0000 h s0eic b ff70 h b8 h serial channel 0 error interrupt ctrl. reg. 0000 h s0rbuf feb2 h 59 h serial channel 0 receive buffer reg. (read only) xxxx h s0ric b ff6e h b7 h serial channel 0 receive interrupt control register 0000 h s0tbic b f19c h e ce h serial channel 0 transmit buffer interrupt control register 0000 h s0tbuf feb0 h 58 h serial channel 0 transmit buffer reg. (write only) 0000 h s0tic b ff6c h b6 h serial channel 0 transmit interrupt control register 0000 h sp fe12 h 09 h cpu system stack pointer register fc00 h sscbr f0b4 h e 5a h ssc baudrate register 0000 h ssccon b ffb2 h d9 h ssc control register 0000 h ssceic b ff76 h bb h ssc error interrupt control register 0000 h sscrb f0b2 h e 59 h ssc receive buffer xxxx h sscric b ff74 h ba h ssc receive interrupt control register 0000 h ssctb f0b0 h e 58 h ssc transmit buffer 0000 h ssctic b ff72 h b9 h ssc transmit interrupt control register 0000 h stkov fe14 h 0a h cpu stack overflow pointer register fa00 h stkun fe16 h 0b h cpu stack underflow pointer register fc00 h syscon b ff12 h 89 h cpu system configuration register 1) 0xx0 h syscon1 b f1dc h e ee h cpu system configuration register 1 0000 h syscon2 b f1d0 h e e8 h cpu system configuration register 2 0000 h syscon3 b f1d4 h e ea h cpu system configuration register 3 0000 h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 39 v2.0, 2001-05 t12ic b f190 h e c8 h capcom 6 timer 12 interrupt ctrl. reg. 0000 h t12of f034 h e 1a h capcom 6 timer 12 offset register 0000 h t12p f030 h e 18 h capcom 6 timer 12 period register 0000 h t13ic b f198 h e cc h capcom 6 timer 13 interrupt ctrl. reg. 0000 h t13p f032 h e 19 h capcom 6 timer 13 period register 0000 h t14 f0d2 h e 69 h rtc timer 14 register no t14rel f0d0 h e 68 h rtc timer 14 reload register no t2 fe40 h 20 h gpt1 timer 2 register 0000 h t2con b ff40 h a0 h gpt1 timer 2 control register 0000 h t2ic b ff60 h b0 h gpt1 timer 2 interrupt control register 0000 h t3 fe42 h 21 h gpt1 timer 3 register 0000 h t3con b ff42 h a1 h gpt1 timer 3 control register 0000 h t3ic b ff62 h b1 h gpt1 timer 3 interrupt control register 0000 h t4 fe44 h 22 h gpt1 timer 4 register 0000 h t4con b ff44 h a2 h gpt1 timer 4 control register 0000 h t4ic b ff64 h b2 h gpt1 timer 4 interrupt control register 0000 h t7 f050 h e 28 h capcom timer 7 register 0000 h t78con b ff20 h 90 h capcom timer 7 and 8 ctrl. reg. 0000 h t7ic b f17a h e bd h capcom timer 7 interrupt ctrl. reg. 0000 h t7rel f054 h e 2a h capcom timer 7 reload register 0000 h t8 f052 h e 29 h capcom timer 8 register 0000 h t8ic b f17c h e be h capcom timer 8 interrupt ctrl. reg. 0000 h t8rel f056 h e 2b h capcom timer 8 reload register 0000 h tfr b ffac h d6 h trap flag register 0000 h trcon b ff34 h 9a h capcom 6 trap enable ctrl. reg. 00xx h wdt feae h 57 h watchdog timer register (read only) 0000 h wdtcon ffae h d7 h watchdog timer control register 2) 00xx h xp0ic b f186 h e c3 h can1 module interrupt control register 0000 h xp1ic b f18e h e c7 h unassigned interrupt control reg. 0000 h table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 40 v2.0, 2001-05 note: the three registers of the otp programming interface are, of course, only implemented in the otp versions of the c164ci. xp3ic b f19e h e cf h pll/rtc interrupt control register 0000 h zeros b ff1c h 8e h constant value 0 ? s register (read only) 0000 h 1) the system configuration is selected during reset. 2) the reset value depends on the indicated reset source. table 7 c164ci registers, ordered by name (cont ? d) name physical address 8-bit addr. description reset value
c164ci/si c164cl/sl data sheet 41 v2.0, 2001-05 absolute maximum ratings note: stresses above those listed under ? absolute maximum ratings ? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. during absolute maximum rating overload conditions ( v in > v dd or v in < v ss ) the voltage on v dd pins with respect to ground ( v ss ) must not exceed the values defined by the absolute maximum ratings. table 8 absolute maximum rating parameters parameter symbol limit values unit notes min. max. storage temperature t st -65 150 c ? junction temperature t j -40 150 c under bias voltage on v dd pins with respect to ground ( v ss ) v dd -0.5 6.5 v ? voltage on any pin with respect to ground ( v ss ) v in -0.5 v dd + 0.5 v ? input current on any pin during overload condition ? -10 10 ma ? absolute sum of all input currents during overload condition ?? | 100 | ma ? power dissipation p diss ? 1.5 w ?
c164ci/si c164cl/sl data sheet 42 v2.0, 2001-05 operating conditions the following operating conditions must not be exceeded in order to ensure correct operation of the c164ci. all parameters specified in the following sections refer to these operating conditions, unless otherwise noticed. table 9 operating condition parameters parameter symbol limit values unit notes min. max. digital supply voltage v dd 4.75 5.5 v active mode, f cpumax = 25 mhz 2.5 1) 1) output voltages and output currents will be reduced when v dd leaves the range defined for active mode. 5.5 v powerdown mode digital ground voltage v ss 0 v reference voltage overload current i ov ? 5 ma per pin 2)3) 2) overload conditions occur if the standard operatings conditions are exceeded, i.e. the voltage on any pin exceeds the specified range (i.e. v ov > v dd + 0.5 v or v ov < v ss - 0.5 v). the absolute sum of input overload currents on all pins may not exceed 50 ma . the supply voltage must remain within the specified limits. proper operation is not guaranteed if overload conditions occur on functional pins line xtal1, rd , wr , etc. 3) not 100% tested, guaranteed by design and characterization. absolute sum of overload currents | i ov | ? 50 ma 3) external load capacitance c l ? 100 pf pin drivers in default mode 4)5) 4) the timing is valid for pin drivers operating in default current mode (selected after reset). reducing the output current may lead to increased delays or reduced driving capability ( c l ). 5) the current rom-version of the c164ci is equipped with port drivers, which provide reduced driving capability and reduced control. please refer to the actual errata sheet for details. ambient temperature t a 070 c sab-c164ci ? -40 85 c saf-c164ci ? -40 125 c sak-c164ci ?
c164ci/si c164cl/sl data sheet 43 v2.0, 2001-05 parameter interpretation the parameters listed in the following partly represent the characteristics of the c164ci and partly its demands on the system. to aid in interpreting the parameters right, when evaluating them for a design, they are marked in column ? symbol ? : cc ( c ontroller c haracteristics): the logic of the c164ci will provide signals with the respective characteristics. sr ( s ystem r equirement): the external system must provide signals with the respective characteristics to the c164ci. dc characteristics (operating conditions apply) 1) parameter symbol limit values unit test conditions min. max. input low voltage (ttl, all except xtal1) v il sr -0.5 0.2 v dd - 0.1 v ? input low voltage xtal1 v il2 sr -0.5 0.3 v dd v ? input low voltage (special threshold) v ils sr -0.5 2.0 v ? input high voltage (ttl, all except rstin , xtal1) v ih sr 0.2 v dd + 0.9 v dd + 0.5 v ? input high voltage rstin (when operated as input) v ih1 sr 0.6 v dd v dd + 0.5 v ? input high voltage xtal1 v ih2 sr 0.7 v dd v dd + 0.5 v ? input high voltage (special threshold) v ihs sr 0.8 v dd - 0.2 v dd + 0.5 v ? input hysteresis (special threshold) hys 400 ? mv series resistance = 0 ? output low voltage 2) v ol cc ? 1.0 v i ol i olmax 3) ? 0.45 v i ol i olnom 3)4) output high voltage 5) v oh cc v dd - 1.0 ? v i oh i ohmax 3) v dd - 0.45 ? v i oh i ohnom 3)4) input leakage current (port 5) i oz1 cc ? 200 na 0 v < v in < v dd
c164ci/si c164cl/sl data sheet 44 v2.0, 2001-05 input leakage current (all other) i oz2 cc ? 500 na 0.45 v < v in < v dd rstin inactive current 6) i rsth 7) ? -10 a v in = v ih1 rstin active current 6) i rstl 8) -100 ? a v in = v il rd /wr inact. current 9) i rwh 7) ? -40 a v out = 2.4 v rd /wr active current 9) i rwl 8) -500 ? a v out = v olmax ale inactive current 9) i alel 7) ? 40 a v out = v olmax ale active current 9) i aleh 8) 500 ? a v out = 2.4 v port 4 inactive current 9) i p4h 7) ? -40 a v out = 2.4 v port 4 active current 9) i p4l 8) -500 ? a v out = v ol1max port0 configuration current 10) i p0h 7) ? -10 a v in = v ihmin i p0l 8) -100 ? a v in = v ilmax xtal1 input current i il cc ? 20 a0 v < v in < v dd pin capacitance 11) (digital inputs/outputs) c io cc ? 10 pf f = 1 mhz t a = 25 c 1) keeping signal levels within the levels specified in this table, ensures operation without overload conditions. for signal levels outside these specifications also refer to the specification of the overload current i ov . 2) for pin rstin this specification is only valid in bidirectional reset mode. 3) the maximum deliverable output current of a port driver depends on the selected output driver mode, see table 10 , current limits for port output drivers . the limit for pin groups must be respected. 4) as a rule, with decreasing output current the output levels approach the respective supply level ( v ol v ss , v oh v dd ). however, only the levels for nominal output currents are guaranteed. 5) this specification is not valid for outputs which are switched to open drain mode. in this case the respective output will float and the voltage results from the external circuitry. 6) these parameters describe the rstin pullup, which equals a resistance of ca. 50 to 250 k ? . 7) the maximum current may be drawn while the respective signal line remains inactive. 8) the minimum current must be drawn in order to drive the respective signal line active. 9) this specification is valid during reset and during adapt-mode. the port 4 current values are only valid for pins p4.3-0, which can act as cs outputs. 10) this specification is valid during reset if required for configuration, and during adapt-mode. 11) not 100% tested, guaranteed by design and characterization. dc characteristics (cont ? d) (operating conditions apply) 1) parameter symbol limit values unit test conditions min. max.
c164ci/si c164cl/sl data sheet 45 v2.0, 2001-05 table 10 current limits for port output drivers port output driver mode maximum output current ( i olmax , - i ohmax ) 1) nominal output current ( i olnom , - i ohnom ) 2) strong driver 10 ma 2.5 ma medium driver 4.0 ma 1.0 ma weak driver 0.5 ma 0.1 ma 1) an output current above | i oxnom | may be drawn from up to three pins at the same time. for any group of 16 neighboring port output pins the total output current in each direction ( i ol and - i oh ) must remain below 50 ma. 2) the current rom-version of the c164ci (step ax) is equipped with port drivers, which provide reduced driving capability and reduced control. please refer to the actual errata sheet for details. power consumption c164ci (rom) (operating conditions apply) parameter sym- bol limit values unit test conditions min. max. power supply current (active) with all peripherals active i dd ? 1 + 2.5 f cpu ma rstin = v il f cpu in [mhz] 1) 1) the supply current is a function of the operating frequency. this dependency is illustrated in figure 9 . these parameters are tested at v ddmax and maximum cpu clock with all outputs disconnected and all inputs at v il or v ih . idle mode supply current with all peripherals active i idx ? 1 + 1.1 f cpu ma rstin = v ih1 f cpu in [mhz] 1) idle mode supply current with all peripherals deactivated, pll off, sdd factor = 32 i ido 2) 2) this parameter is determined mainly by the current consumed by the oscillator (see figure 8 ). this current, however, is influenced by the external oscillator circuitry (crystal, capacitors). the values given refer to a typical circuitry and may change in case of a not optimized external oscillator circuitry. ? 500 + 50 f osc arstin = v ih1 f osc in [mhz] 1) sleep and power-down mode supply current with rtc running i pdr 2) ? 200 + 25 f osc a v dd = v ddmax f osc in [mhz] 3) 3) this parameter is tested including leakage currents. all inputs (including pins configured as inputs) at 0 v to 0.1 v or at v dd - 0.1 v to v dd , v ref = 0 v, all outputs (including pins configured as outputs) disconnected. sleep and power-down mode supply current with rtc disabled i pdo ? 50 a v dd = v ddmax 3)
c164ci/si c164cl/sl data sheet 46 v2.0, 2001-05 power consumption c164ci (otp) (operating conditions apply) parameter sym- bol limit values unit test conditions min. max. power supply current (active) with all peripherals active i dd ? 10 + 3.5 f cpu ma rstin = v il f cpu in [mhz] 1) idle mode supply current with all peripherals active i idx ? 5 + 1.25 f cpu ma rstin = v ih1 f cpu in [mhz] 1) idle mode supply current with all peripherals deactivated, pll off, sdd factor = 32 i ido 2) ? 500 + 50 f osc arstin = v ih1 f osc in [mhz] 1) sleep and power-down mode supply current with rtc running i pdr 2) ? 200 + 25 f osc a v dd = v ddmax f osc in [mhz] 3) sleep and power-down mode supply current with rtc disabled i pdo ? 50 a v dd = v ddmax 3) 1) the supply current is a function of the operating frequency. this dependency is illustrated in figure 10 . these parameters are tested at v ddmax and maximum cpu clock with all outputs disconnected and all inputs at v il or v ih . 2) this parameter is determined mainly by the current consumed by the oscillator (see figure 8 ). this current, however, is influenced by the external oscillator circuitry (crystal, capacitors). the values given refer to a typical circuitry and may change in case of a not optimized external oscillator circuitry. 3) this parameter is tested including leakage currents. all inputs (including pins configured as inputs) at 0 v to 0.1 v or at v dd - 0.1 v to v dd , v ref = 0 v, all outputs (including pins configured as outputs) disconnected.
c164ci/si c164cl/sl data sheet 47 v2.0, 2001-05 figure 8 idle and power down supply current as a function of oscillator frequency mcd04433 0 f osc pdomax i 4 8 12 16 0 250 mhz a 500 750 1000 1250 1500 pdrmax i idotyp i idomax i
c164ci/si c164cl/sl data sheet 48 v2.0, 2001-05 figure 9 supply/idle current as a function of operating frequency for rom derivatives i [ma] f cpu [mhz] 10 15 20 25 i dd5max i dd5typ i idx5max i idx5typ 20 40 60 80 100
c164ci/si c164cl/sl data sheet 49 v2.0, 2001-05 figure 10 supply/idle current as a function of operating frequency for otp derivatives i [ma] f cpu [mhz] 10 15 20 25 i dd5max i dd5typ i idx5max i idx5typ 20 40 60 80 100
c164ci/si c164cl/sl data sheet 50 v2.0, 2001-05 ac characteristics definition of internal timing the internal operation of the c164ci is controlled by the internal cpu clock f cpu . both edges of the cpu clock can trigger internal (e.g. pipeline) or external (e.g. bus cycles) operations. the specification of the external timing (ac characteristics) therefore depends on the time between two consecutive edges of the cpu clock, called ? tcl ? (see figure 11 ). figure 11 generation mechanisms for the cpu clock the cpu clock signal f cpu can be generated from the oscillator clock signal f osc via different mechanisms. the duration of tcls and their variation (and also the derived external timing) depends on the used mechanism to generate f cpu . this influence must be regarded when calculating the timings for the c164ci. note: the example for pll operation shown in figure 11 refers to a pll factor of 4. the used mechanism to generate the basic cpu clock is selected by bitfield clkcfg in register rp0h.7-5. upon a long hardware reset register rp0h is loaded with the logic levels present on the upper half of port0 (p0h), i.e. bitfield clkcfg represents the logic levels on pins mct04338 f osc f cpu phase locked loop operation tcl f osc f cpu direct clock drive f osc f cpu prescaler operation tcl tcl tcl tcl tcl
c164ci/si c164cl/sl data sheet 51 v2.0, 2001-05 p0.15-13 (p0h.7-5). register rp0h can be loaded from the upper half of register rstcon under software control. table 11 associates the combinations of these three bits with the respective clock generation mode. prescaler operation when prescaler operation is configured (clkcfg = 001 b ) the cpu clock is derived from the internal oscillator (input clock signal) by a 2:1 prescaler. the frequency of f cpu is half the frequency of f osc and the high and low time of f cpu (i.e. the duration of an individual tcl) is defined by the period of the input clock f osc . the timings listed in the ac characteristics that refer to tcls therefore can be calculated using the period of f osc for any tcl. phase locked loop when pll operation is configured (via clkcfg) the on-chip phase locked loop is enabled and provides the cpu clock (see table 11 ). the pll multiplies the input frequency by the factor f which is selected via the combination of pins p0.15-13 (i.e. f cpu = f osc f ). with every f ? th transition of f osc the pll circuit synchronizes the cpu clock to the input clock. this synchronization is done smoothly, i.e. the cpu clock frequency does not change abruptly. table 11 c164ci clock generation modes clkcfg 1) (rp0h.7-5) 1) please note that pin p0.15 (corresponding to rp0h.7) is inverted in emulation mode, and thus also in ehm. cpu frequency f cpu = f osc f external clock input range 2) 2) the external clock input range refers to a cpu clock range of 10 ? 25 mhz. notes 11 1 f osc 4 2.5 to 6.25 mhz default configuration 110 f osc 3 3.33 to 8.33 mhz ? 101 f osc 2 5 to 12.5 mhz ? 100 f osc 5 2 to 5 mhz ? 011 f osc 1 1 to 25 mhz direct drive 3) 3) the maximum frequency depends on the duty cycle of the external clock signal. 010 f osc 1.5 6.66 to 16.66 mhz ? 001 f osc / 2 2 to 50 mhz cpu clock via prescaler 000 f osc 2.5 4 to 10 mhz ?
c164ci/si c164cl/sl data sheet 52 v2.0, 2001-05 due to this adaptation to the input clock the frequency of f cpu is constantly adjusted so it is locked to f osc . the slight variation causes a jitter of f cpu which also effects the duration of individual tcls. the timings listed in the ac characteristics that refer to tcls therefore must be calculated using the minimum tcl that is possible under the respective circumstances. the actual minimum value for tcl depends on the jitter of the pll. as the pll is constantly adjusting its output frequency so it corresponds to the applied input frequency (crystal or oscillator) the relative deviation for periods of more than one tcl is lower than for one single tcl (see formula and figure 12 ). for a period of n tcl the minimum value is computed using the corresponding deviation d n : ( n tcl) min = n tcl nom - d n ; d n [ns] = (13.3 + n 6.3)/ f cpu [mhz], where n = number of consecutive tcls and 1 n 40. so for a period of 3 tcls @ 25 mhz (i.e. n = 3): d 3 = (13.3 + 3 6.3)/25 = 1.288 ns, and (3tcl) min = 3tcl nom - 1.288 ns = 58.7 ns (@ f cpu = 25 mhz). this is especially important for bus cycles using waitstates and e.g. for the operation of timers, serial interfaces, etc. for all slower operations and longer periods (e.g. pulse train generation or measurement, lower baudrates, etc.) the deviation caused by the pll jitter is neglectible. note: for all periods longer than 40 tcl the n = 40 value can be used (see figure 12 ). figure 12 approximated maximum accumulated pll jitter mcd04455 n max. jitter d n 1 10 20 30 ns 26.5 110 20 40 this approximated formula is valid for 1 n 40 and 10 mhz f cpu 25 mhz. 10 mhz 16 mhz 20 mhz 25 mhz 30 < ? < ? < ? < ?
c164ci/si c164cl/sl data sheet 53 v2.0, 2001-05 direct drive when direct drive is configured (clkcfg = 011 b ) the on-chip phase locked loop is disabled and the cpu clock is directly driven from the internal oscillator with the input clock signal. the frequency of f cpu directly follows the frequency of f osc so the high and low time of f cpu (i.e. the duration of an individual tcl) is defined by the duty cycle of the input clock f osc . the timings listed below that refer to tcls therefore must be calculated using the minimum tcl that is possible under the respective circumstances. this minimum value can be calculated via the following formula: tcl min = 1/ f osc dc min (dc = duty cycle) for two consecutive tcls the deviation caused by the duty cycle of f osc is compensated so the duration of 2tcl is always 1/ f osc . the minimum value tcl min therefore has to be used only once for timings that require an odd number of tcls (1, 3, ? ). timings that require an even number of tcls (2, 4, ? ) may use the formula 2tcl = 1/ f osc .
c164ci/si c164cl/sl data sheet 54 v2.0, 2001-05 ac characteristics external clock drive xtal1 (operating conditions apply) figure 13 external clock drive xtal1 note: if the on-chip oscillator is used together with a crystal, the oscillator frequency is limited to a range of 4 mhz to 16 mhz. it is strongly recommended to measure the oscillation allowance (or margin) in the final target system (layout) to determine the optimum parameters for the oscillator operation. please refer to the limits specified by the crystal supplier. when driven by an external clock signal it will accept the specified frequency range. operation at lower input frequencies is possible but is guaranteed by design only (not 100% tested). table 12 external clock drive characteristics parameter symbol direct drive 1:1 prescaler 2:1 pll 1:n unit min. max. min. max. min. max. oscillator period t osc sr 40 ? 20 ? 60 1) 1) the minimum and maximum oscillator periods for pll operation depend on the selected cpu clock generation mode. please see respective table above. 500 1) ns high time 2) 2) the clock input signal must reach the defined levels v il2 and v ih2 . t 1 sr 20 3) 3) the minimum high and low time refers to a duty cycle of 50%. the maximum operating freqency ( f cpu ) in direct drive mode depends on the duty cycle of the clock input signal. ? 6 ? 10 ? ns low time 2) t 2 sr 20 3) ? 6 ? 10 ? ns rise time 2) t 3 sr ? 8 ? 5 ? 10 ns fall time 2) t 4 sr ? 8 ? 5 ? 10 ns mct02534 3 t 4 t v ih2 v il v dd 0.5 1 t 2 t osc t
c164ci/si c164cl/sl data sheet 55 v2.0, 2001-05 a/d converter characteristics (operating conditions apply) table 13 a/d converter characteristics parameter symbol limit values unit test conditions min. max. analog reference supply v aref sr 4.0 v dd + 0.1 v 1) 1) tue is tested at v aref =5.0v, v agnd =0v, v dd = 4.9 v. it is guaranteed by design for all other voltages within the defined voltage range. if the analog reference supply voltage exceeds the power supply voltage by up to 0.2 v (i.e. v aref = v dd = +0.2 v) the maximum tue is increased to 3 lsb. this range is not 100% tested. the specified tue is guaranteed only if the absolute sum of input overload currents on port 5 pins (see i ov specification) does not exceed 10 ma. during the reset calibration sequence the maximum tue may be 4 lsb. analog reference ground v agnd sr v ss - 0.1 v ss + 0.2 v ? analog input voltage range v ain sr v agnd v aref v 2) 2) v ain may exceed v agnd or v aref up to the absolute maximum ratings. however, the conversion result in these cases will be x000 h or x3ff h , respectively. basic clock frequency f bc 0.5 6.25 mhz 3) 3) the limit values for f bc must not be exceeded when selecting the cpu frequency and the adctc setting. conversion time t c cc ? 40 t bc + t s + 2 t cpu ? 4) t cpu = 1 / f cpu 4) this parameter includes the sample time t s , the time for determining the digital result and the time to load the result register with the conversion result. values for the basic clock t bc depend on programming and can be taken from table 14 . this parameter depends on the adc control logic. it is not a real maximum value, but rather a fixum. calibration time after reset t cal cc ? 3328 t bc ? 5) 5) during the reset calibration conversions can be executed (with the current accuracy). the time required for these conversions is added to the total reset calibration time. total unadjusted error tue cc ? 2lsb 1) internal resistance of reference voltage source r aref sr ? t bc / 60 - 0.25 k ? t bc in [ns] 6)7) 6) during the conversion the adc ? s capacitance must be repeatedly charged or discharged. the internal resistance of the reference voltage source must allow the capacitance to reach its respective voltage level within each conversion step. the maximum internal resistance results from the programmed conversion timing. 7) not 100% tested, guaranteed by design and characterization. internal resistance of analog source r asrc sr ? t s / 450 - 0.25 k ? t s in [ns] 7)8) adc input capacitance c ain cc ? 33 pf 7)
c164ci/si c164cl/sl data sheet 56 v2.0, 2001-05 sample time and conversion time of the c164ci ? s a/d converter are programmable. table 14 should be used to calculate the above timings. the limit values for f bc must not be exceeded when selecting adctc. converter timing example: assumptions: f cpu = 25 mhz (i.e. t cpu = 40 ns), adctc = ? 00 ? , adstc = ? 00 ? . basic clock f bc = f cpu /4 = 6.25 mhz, i.e. t bc = 160 ns. sample time t s = t bc 8 = 1280 ns. conversion time t c = t s + 40 t bc + 2 t cpu = (1280 + 6400 + 80) ns = 7.8 s. 8) during the sample time the input capacitance c ain can be charged/discharged by the external source. the internal resistance of the analog source must allow the capacitance to reach its final voltage level within t s . after the end of the sample time t s , changes of the analog input voltage have no effect on the conversion result. values for the sample time t s depend on programming and can be taken from table 14 . table 14 a/d converter computation table adcon.15|14 (adctc) a/d converter basic clock f bc adcon.13|12 (adstc) sample time t s 00 f cpu / 4 00 t bc 8 01 f cpu / 2 01 t bc 16 10 f cpu / 16 10 t bc 32 11 f cpu / 8 11 t bc 64
c164ci/si c164cl/sl data sheet 57 v2.0, 2001-05 testing waveforms figure 14 input output waveforms figure 15 float waveforms mca04414 2.4 v 0.45 v 1.8 v 0.8 v 1.8 v 0.8 v test points ac inputs during testing are driven at 2.4 v for a logic ? 1 ? and 0.45 v for a logic ? 0 ? . timing measurements are made at ih v min for a logic ? 1 ? and v il max for a logic ? 0 ? . mca00763 - 0.1 v + 0.1 v + 0.1 v - 0.1 v reference for timing purposes a port pin is no longer floating when a 100 mv change from load voltage occurs, but begins to float when a 100 mv change from the loaded oh v timing points load v v load oh v v ol / v ol level occurs ( i oh ol i / = 20 ma).
c164ci/si c164cl/sl data sheet 58 v2.0, 2001-05 memory cycle variables the timing tables below use three variables which are derived from the busconx registers and represent the special characteristics of the programmed memory cycle. the following table describes, how these variables are to be computed. note: please respect the maximum operating frequency of the respective derivative. ac characteristics table 15 memory cycle variables description symbol values ale extension t a tcl memory cycle time waitstates t c 2tcl (15 - ) memory tristate time t f 2tcl (1 - ) multiplexed bus (operating conditions apply) ale cycle time = 6 tcl + 2 t a + t c + t f (120 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max. ale high time t 5 cc 10 + t a ? tcl - 10 + t a ? ns address setup to ale t 6 cc 4 + t a ? tcl - 16 + t a ? ns address hold after ale t 7 cc 10 + t a ? tcl - 10 + t a ? ns ale falling edge to rd , wr (with rw-delay) t 8 cc 10 + t a ? tcl - 10 + t a ? ns ale falling edge to rd , wr (no rw-delay) t 9 cc -10 + t a ? -10 + t a ? ns address float after rd , wr (with rw-delay) t 10 cc ? 6 ? 6ns address float after rd , wr (no rw-delay) t 11 cc ? 26 ? tcl + 6 ns rd , wr low time (with rw-delay) t 12 cc 30 + t c ? 2tcl - 10 + t c ? ns
c164ci/si c164cl/sl data sheet 59 v2.0, 2001-05 rd , wr low time (no rw-delay) t 13 cc 50 + t c ? 3tcl - 10 + t c ? ns rd to valid data in (with rw-delay) t 14 sr ? 20 + t c ? 2tcl - 20 + t c ns rd to valid data in (no rw-delay) t 15 sr ? 40 + t c ? 3tcl - 20 + t c ns ale low to valid data in t 16 sr ? 40 + t a + t c ? 3tcl - 20 + t a + t c ns address to valid data in t 17 sr ? 50 + 2 t a + t c ? 4tcl - 30 + 2 t a + t c ns data hold after rd rising edge t 18 sr 0 ? 0 ? ns data float after rd t 19 sr ? 26 + t f ? 2tcl - 14 + t f ns data valid to wr t 22 cc 20 + t c ? 2tcl - 20 + t c ? ns data hold after wr t 23 cc 26 + t f ? 2tcl - 14 + t f ? ns ale rising edge after rd , wr t 25 cc 26 + t f ? 2tcl - 14 + t f ? ns address hold after rd , wr t 27 cc 26 + t f ? 2tcl - 14 + t f ? ns ale falling edge to cs 1) t 38 cc -4 - t a 10 - t a -4 - t a 10 - t a ns cs low to valid data in 1) t 39 sr ? 40 + t c + 2 t a ? 3tcl - 20 + t c + 2 t a ns cs hold after rd , wr 1) t 40 cc 46 + t f ? 3tcl - 14 + t f ? ns ale fall. edge to rdcs , wrcs (with rw delay) t 42 cc 16 + t a ? tcl - 4 + t a ? ns multiplexed bus (cont ? d) (operating conditions apply) ale cycle time = 6 tcl + 2 t a + t c + t f (120 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max.
c164ci/si c164cl/sl data sheet 60 v2.0, 2001-05 ale fall. edge to rdcs , wrcs (no rw delay) t 43 cc -4 + t a ? -4 + t a ? ns address float after rdcs , wrcs (with rw delay) t 44 cc ? 0 ? 0ns address float after rdcs , wrcs (no rw delay) t 45 cc ? 20 ? tcl ns rdcs to valid data in (with rw delay) t 46 sr ? 16 + t c ? 2tcl - 24 + t c ns rdcs to valid data in (no rw delay) t 47 sr ? 36 + t c ? 3tcl - 24 + t c ns rdcs , wrcs low time (with rw delay) t 48 cc 30 + t c ? 2tcl - 10 + t c ? ns rdcs , wrcs low time (no rw delay) t 49 cc 50 + t c ? 3tcl - 10 + t c ? ns data valid to wrcs t 50 cc 26 + t c ? 2tcl - 14 + t c ? ns data hold after rdcs t 51 sr 0 ? 0 ? ns data float after rdcs t 52 sr ? 20 + t f ? 2tcl - 20 + t f ns address hold after rdcs , wrcs t 54 cc 20 + t f ? 2tcl - 20 + t f ? ns data hold after wrcs t 56 cc 20 + t f ? 2tcl - 20 + t f ? ns 1) these parameters refer to the latched chip select signals (csxl ). the early chip select signals (csxe ) are specified together with the address and signal bhe (see figures below). multiplexed bus (cont ? d) (operating conditions apply) ale cycle time = 6 tcl + 2 t a + t c + t f (120 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max.
c164ci/si c164cl/sl data sheet 61 v2.0, 2001-05 figure 16 external memory cycle: multiplexed bus, with read/write delay, normal ale a21-a16 (a15-a8) bhe , csxe data in data out address address t 38 t 44 t 10 address ale csxl bus read cycle rd rdcsx bus write cycle wr , wrl , wrh wrcsx t 5 t 16 t 17 t 6 t 7 t 39 t 40 t 25 t 27 t 18 t 19 t 14 t 46 t 12 t 48 t 10 t 22 t 23 t 44 t 12 t 48 t 8 t 42 t 42 t 8 t 50 t 51 t 54 t 52 t 56
c164ci/si c164cl/sl data sheet 62 v2.0, 2001-05 figure 17 external memory cycle: multiplexed bus, with read/write delay, extended ale data out address data in address t 38 t 4 t 10 address ale csxl a21-a16 (a15-a8) bhe , csxe bus read cycle rd rdcsx bus write cycle wr , wrl , wrh wrcsx t 5 t 16 t 17 t 6 t 7 t 39 t 40 t 25 t 27 t 18 t 19 t 14 t 46 t 12 t 48 t 10 t 22 t 23 t 44 t 12 t 48 t 8 t 42 t 42 t 8 t 50 t 51 t 54 t 52 t 56
c164ci/si c164cl/sl data sheet 63 v2.0, 2001-05 figure 18 external memory cycle: multiplexed bus, no read/write delay, normal ale data out address address data in t 38 address ale csxl a21-a16 (a15-a8) bhe , csxe bus read cycle rd rdcsx bus write cycle wr , wrl , wrh wrcsx t 5 t 16 t 17 t 6 t 7 t 39 t 40 t 25 t 27 t 18 t 19 t 15 t 47 t 13 t 49 t 22 t 23 t 13 t 49 t 9 t 43 t 43 t 9 t 11 t 45 t 11 t 45 t 50 t 51 t 54 t 52 t 56
c164ci/si c164cl/sl data sheet 64 v2.0, 2001-05 figure 19 external memory cycle: multiplexed bus, no read/write delay, extended ale data out address data in address t 38 address ale csxl a21-a16 (a15-a8) bhe , csxe bus read cycle rd rdcsx bus write cycle wr , wrl , wrh wrcsx t 5 t 16 t 17 t 6 t 7 t 39 t 40 t 25 t 27 t 18 t 19 t 15 t 47 t 13 t 49 t 22 t 23 t 13 t 49 t 9 t 43 t 43 t 9 t 11 t 45 t 11 t 45 t 50 t 51 t 54 t 52 t 56
c164ci/si c164cl/sl data sheet 65 v2.0, 2001-05 ac characteristics demultiplexed bus (operating conditions apply) ale cycle time = 4 tcl + 2 t a + t c + t f (80 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max. ale high time t 5 cc 10 + t a ? tcl - 10 + t a ? ns address setup to ale t 6 cc 4 + t a ? tcl - 16 + t a ? ns ale falling edge to rd , wr (with rw-delay) t 8 cc 10 + t a ? tcl - 10 + t a ? ns ale falling edge to rd , wr (no rw-delay) t 9 cc -10 + t a ? -10 + t a ? ns rd , wr low time (with rw-delay) t 12 cc 30 + t c ? 2tcl - 10 + t c ? ns rd , wr low time (no rw-delay) t 13 cc 50 + t c ? 3tcl - 10 + t c ? ns rd to valid data in (with rw-delay) t 14 sr ? 20 + t c ? 2tcl - 20 + t c ns rd to valid data in (no rw-delay) t 15 sr ? 40 + t c ? 3tcl - 20 + t c ns ale low to valid data in t 16 sr ? 40 + t a + t c ? 3tcl - 20 + t a + t c ns address to valid data in t 17 sr ? 50 + 2 t a + t c ? 4tcl - 30 + 2 t a + t c ns data hold after rd rising edge t 18 sr 0 ? 0 ? ns data float after rd rising edge (with rw-delay 1) ) t 20 sr ? 26 + 2 t a + t f 1) ? 2tcl - 14 + 22 t a + t f 1) ns data float after rd rising edge (no rw-delay 1) ) t 21 sr ? 10 + 2 t a + t f 1) ? tcl - 10 + 22 t a + t f 1) ns
c164ci/si c164cl/sl data sheet 66 v2.0, 2001-05 data valid to wr t 22 cc 20 + t c ? 2tcl - 20 + t c ? ns data hold after wr t 24 cc 10 + t f ? tcl - 10 + t f ? ns ale rising edge after rd , wr t 26 cc -10 + t f ? -10 + t f ? ns address hold after wr 2) t 28 cc 0 + t f ? 0 + t f ? ns ale falling edge to cs 3) t 38 cc -4 - t a 10 - t a -4 - t a 10 - t a ns cs low to valid data in 3) t 39 sr ? 40 + t c + 2 t a ? 3tcl - 20 + t c + 2 t a ns cs hold after rd , wr 3) t 41 cc 6 + t f ? tcl - 14 + t f ? ns ale falling edge to rdcs , wrcs (with rw-delay) t 42 cc 16 + t a ? tcl - 4 + t a ? ns ale falling edge to rdcs , wrcs (no rw-delay) t 43 cc -4 + t a ? -4 + t a ? ns rdcs to valid data in (with rw-delay) t 46 sr ? 16 + t c ? 2tcl - 24 + t c ns rdcs to valid data in (no rw-delay) t 47 sr ? 36 + t c ? 3tcl - 24 + t c ns rdcs , wrcs low time (with rw-delay) t 48 cc 30 + t c ? 2tcl - 10 + t c ? ns rdcs , wrcs low time (no rw-delay) t 49 cc 50 + t c ? 3tcl - 10 + t c ? ns data valid to wrcs t 50 cc 26 + t c ? 2tcl - 14 + t c ? ns data hold after rdcs t 51 sr 0 ? 0 ? ns data float after rdcs (with rw-delay) 1) t 53 sr ? 20 + t f ? 2tcl - 20 + 2 t a + t f 1) ns demultiplexed bus (cont ? d) (operating conditions apply) ale cycle time = 4 tcl + 2 t a + t c + t f (80 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max.
c164ci/si c164cl/sl data sheet 67 v2.0, 2001-05 data float after rdcs (no rw-delay) 1) t 68 sr ? 0 + t f ? tcl - 20 + 2 t a + t f 1) ns address hold after rdcs , wrcs t 55 cc -6 + t f ? -6 + t f ? ns data hold after wrcs t 57 cc 6 + t f ? tcl - 14 + t f ? ns 1) rw-delay and t a refer to the next following bus cycle (including an access to an on-chip x-peripheral). 2) read data are latched with the same clock edge that triggers the address change and the rising rd edge. therefore address changes before the end of rd have no impact on read cycles. 3) these parameters refer to the latched chip select signals (csxl ). the early chip select signals (csxe ) are specified together with the address and signal bhe (see figures below). demultiplexed bus (cont ? d) (operating conditions apply) ale cycle time = 4 tcl + 2 t a + t c + t f (80 ns at 25 mhz cpu clock without waitstates) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max.
c164ci/si c164cl/sl data sheet 68 v2.0, 2001-05 figure 20 external memory cycle: demultiplexed bus, with read/write delay, normal ale data out data in t 38 address ale csxl a21-a16 a15-a0 bhe , csxe bus (d15-d8) d7-d0 read cycle rd rdcsx write cycle wrcsx t 5 t 16 t 17 t 6 t 39 t 41 t 26 t 28 t 18 t 20 t 14 t 46 t 12 t 48 t 22 t 24 t 12 t 48 t 8 t 42 t 42 t 8 t 50 t 51 t 55 t 53 t 57 bus (d15-d8) d7-d0 wr , wrl , wrh
c164ci/si c164cl/sl data sheet 69 v2.0, 2001-05 figure 21 external memory cycle: demultiplexed bus, with read/write delay, extended ale data out data in t 38 address ale csxl a21-a16 a15-a0 bhe , csxe read cycle rd rdcsx write cycle wrcsx t 5 t 16 t 17 t 6 t 39 t 41 t 26 t 28 t 18 t 20 t 14 t 46 t 12 t 48 t 22 t 24 t 12 t 48 t 8 t 42 t 42 t 8 t 50 t 51 t 55 t 53 t 57 bus (d15-d8) d7-d0 bus (d15-d8) d7-d0 wr , wrl , wrh
c164ci/si c164cl/sl data sheet 70 v2.0, 2001-05 figure 22 external memory cycle: demultiplexed bus, no read/write delay, normal ale data out data in t 38 address ale csxl a21-a16 a15-a0 bhe , csxe read cycle rd rdcsx write cycle wrcsx t 5 t 16 t 17 t 6 t 39 t 41 t 26 t 28 t 18 t 21 t 15 t 47 t 13 t 49 t 22 t 24 t 13 t 49 t 9 t 43 t 43 t 9 t 50 t 51 t 55 t 68 t 57 bus (d15-d8) d7-d0 bus (d15-d8) d7-d0 wr , wrl ,wrh
c164ci/si c164cl/sl data sheet 71 v2.0, 2001-05 figure 23 external memory cycle: demultiplexed bus, no read/write delay, extended ale data out data in t 38 address ale csxl a21-a16 a15-a0 bhe , csxe read cycle rd rdcsx write cycle wr , wrl , wrh wrcsx t 5 t 16 t 17 t 6 t 39 t 41 t 26 t 28 t 18 t 21 t 15 t 47 t 13 t 49 t 22 t 24 t 13 t 49 t 9 t 43 t 43 t 9 t 50 t 51 t 55 t 68 t 57 bus (d15-d8) d7-d0 bus (d15-d8) d7-d0
c164ci/si c164cl/sl data sheet 72 v2.0, 2001-05 ac characteristics figure 24 clkout timing notes 1) cycle as programmed, including mctc waitstates (example shows 0 mctc ws). 2) the leading edge of the respective command depends on rw-delay. 3) multiplexed bus modes have a mux waitstate added after a bus cycle, and an additional mttc waitstate may be inserted here. for a multiplexed bus with mttc waitstate this delay is 2 clkout cycles, for a demultiplexed bus without mttc waitstate this delay is zero. 4) the next external bus cycle may start here. clkout (operating conditions apply) parameter symbol max. cpu clock = 25 mhz variable cpu clock 1 / 2tcl = 1 to 25 mhz unit min. max. min. max. clkout cycle time t 29 cc 40 40 2tcl 2tcl ns clkout high time t 30 cc 14 ? tcl - 6 ? ns clkout low time t 31 cc 10 ? tcl - 10 ? ns clkout rise time t 32 cc ? 4 ? 4ns clkout fall time t 33 cc ? 4 ? 4ns clkout rising edge to ale falling edge t 34 cc 0 + t a 10 + t a 0 + t a 10 + t a ns clkout ale t 30 t 34 mux/tristate 3) t 32 t 33 t 29 running cycle 1) t 31 command rd , wr 2) 4)
c164ci/si c164cl/sl data sheet 73 v2.0, 2001-05 external xram access if xper-share mode is enabled the on-chip xram of the c164ci can be accessed (during hold states) by an external master like an asynchronous sram. figure 25 external access to the xram table 16 xram access timing (operating conditions apply) parameter symbol limit values unit min. max. address setup time before rd /wr falling edge t 40 sr 4 ? ns address hold time after rd /wr rising edge t 41 sr 0 ? ns data turn on delay after rd falling edge read t 42 cc 2 ? ns data output valid delay after address latched t 43 cc ? 37 ns data turn off delay after rd rising edge t 44 cc 0 10 ns write data setup time before wr rising edge write t 45 sr 10 ? ns write data hold time after wr rising edge t 46 sr 1 ? ns wr pulse width t 47 sr 18 ? ns wr signal recovery time t 48 sr t 40 ? ns read data 43 t 42 t 44 t mct04423 (rd, wr) write data command address 40 t 45 t 47 t 46 t 48 t 41 t
c164ci/si c164cl/sl data sheet 74 v2.0, 2001-05 package outlines p-mqfp-80-7 (plastic metric quad flat package) gpm05249 sorts of packing package outlines for tubes, trays etc. are contained in our data book ? package information ? . dimensions in mm smd = surface mounted device
http://www.infineon.com published by infineon technologies ag infineon goes for business excellence ? business excellence means intelligent approaches and clearly defined processes, which are both constantly under review and ultimately lead to good operating results. better operating results and business excellence mean less idleness and wastefulness for all of us, more professional success, more accurate information, a better overview and, thereby, less frustration and more satisfaction. ? dr. ulrich schumacher

▲Up To Search▲

Price & Availability of SAK-C164CI-8EM

	To Download SAK-C164CI-8EM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .